Brake system of cars VAZ-2107

All articles about the device and repair of units and elements of the brake system of VAZ-2107 Zhiguli cars and their modifications.

Description of the brake system design
Front wheel brake mechanism: 1 - guide pin of the pads (2101-3501132); 2 - brake shoe (2101-3501089); 3 - inner working cylinder (2101-3501182/83); 4 - brake shoe pressure spring...

Brake system — checking technical condition
We check the condition of the brake system according to the maintenance schedule (see " Periodic maintenance "). To complete the work you will need a caliper. Sequence of...

Hydraulic brakes — checking the brake fluid level
The brake hydraulic reservoir is located in the engine compartment on the left side and is secured to its bulkhead with a clamp. Sequence of execution 1. Prepare the vehicle for...

Hydraulic brake drive — bleeding and replacing brake fluid
We replace the brake fluid according to the maintenance schedule (see " Periodic maintenance "). We bleed the brake hydraulic drive to remove air from it and when replacing the...

Front Brake Pads — Replacement
Attention! Replace the pads as a set on both sides of the car. Check the condition of the brake shoe linings periodically (see " Brake system - checking technical condition ") and...

Rear Brake Pads — Replacement
Attention! Replace the pads as a set on both sides of the car. Check the condition of the brake shoe linings periodically (see " Brake system - checking technical condition ") and...

Master Brake Cylinder — Removal and Installation
We remove the main brake cylinder for its replacement, as well as when replacing the brake booster. To perform the work you will need an assistant, as well as a special 10 mm...

Vacuum brake booster — checking the functionality
The vacuum booster is installed on the engine compartment partition. The booster is non-separable, if it fails, we replace it entirely. A sign of a malfunction of the brake...

Brake booster — replacement
To perform the work you will need an assistant, as well as a caliper, a special 10 mm wrench for brake pipes, a transparent vinyl tube of a suitable diameter, a container for...

Brake light switch — position adjustment
The free travel of the brake pedal with the engine off should be within 3-5 mm. This value is achieved by adjusting the position of the brake light switch. If the switch is close...

Front wheel brake mechanism — disassembly
The front wheel brake mechanism consists of a caliper, working cylinders, brake disc and pads. We remove the front brake caliper to replace it, the working cylinder or the brake...

Front Brake Hose — Replacement
The work is shown using the example of replacing the brake hose of the right wheel. To perform the work you will need an assistant, as well as a special 10 mm wrench for brake...

Rear Wheel Slave Cylinder — Replacement
We replace the rear wheel slave cylinder if we detect a brake fluid leak or if the pistons are jammed. To perform the work you will need an assistant, as well as a special 10 mm...

Rear Brake Hose — Replacement
To perform the work you will need an assistant, as well as a special 10 mm wrench for brake pipes, a transparent vinyl tube of a suitable diameter, a container for draining the...

Brake pipes — replacement
Before unscrewing the brake pipe fittings, it is necessary to clean the connection points from dirt and apply penetrating lubricant. To unscrew the brake pipe fittings, special...

Brake Pressure Regulator — Checking and Replacing
The pressure regulator is mounted on the body bracket and connected to the rear axle via a torsion arm and rod. Pressure regulator drive parts: 1 - regulator drive lever...

Parking brake — adjustment
If the parking brake system does not hold the vehicle on a 25% slope when the drive lever is moved by 4-6 teeth of the ratchet device, then it is necessary to adjust the stroke of...

Parking brake system — disassembly and assembly
We replace the parking brake system drive cables if they cannot be adjusted due to their stretching or mechanical damage. Parking brake system drive parts: 1 - spacer sleeve...

This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

More articles from other manuals on VAZ cars:
➠ Chassis: Brake system VAZ-11113 (1996-2003)
➠ Chassis: Brake system VAZ-2105 (1979-2010)
➠ Chassis: Brake system VAZ-2101 (1970-1983)
➠ Chassis: Brake system VAZ-2110 (1995-2007)
➠ Chassis: Brake system VAZ-21214 (1994-2006)

Share with friends: