Removal and installation of the front caliper You will need: keys "at 12", "at 15" And "at 17" screwdriver Before starting work: Remove the corresponding wheel. 1. Remove the brake hose seal from the bracket on the strut. 2....
Front caliper repair You will need: key "for 8" thin screwdriver Before starting work: Clean the caliper of dirt. 1. Remove the edge of the protective cap from the cylinder groove. 2. Turning the cap...
Replacing the front brake disc You will need: keys "on 10", "at 12" And "at 17" screwdriver Before starting work: Remove the corresponding wheel. If there are scuffs, deep scratches and other defects on the...
Replacing the protective covers of the front guide pins If the protective covers of the guide pins are damaged, dirt and water can cause the caliper to jam. 1. Remove the caliper without disconnecting the brake hose from it, and hang...
Rear brake drum repair You will need: balloon key, key "at 27" pliers screwdriver hammer jack stand wheel chocks Push the parking brake lever all the way down (the car is disinhibited). Remove the rear...
Replacing the rear wheel cylinder You will need: special wrench for brake pipe nuts key "on 10" Before starting work : Remove the brake pads. 1. Remove dirt from the bolts of the wheel cylinder and the air release...
Wheel cylinder repair Wheel Cylinder Details: 1 - protective cap; 2 - piston; 3 - sealing ring; 4 - spring cup; 5 - spring; 6 - cylinder body; 7 - sealing ring of the valve; 8 - air release valve You...
Replacing the vacuum booster You will need: keys "on 10" And "at 13" screwdriver Remove the spare wheel. If the vacuum booster fails, the resistance of the brake pedal increases significantly, which...
Removal and installation of the main brake cylinder You will need: keys "on 10" And "at 13" screwdriver If a leak is found from the master brake cylinder, remove it from the vehicle and repair the cylinder. Attention! Repair of the...
Repair of the main brake cylinder You will need: key "at 12" socket head "at 22" knob screwdriver Master brake cylinder: 1 - cork; 2 - cylinder body; 3 - fitting; 4 - protective cap; 5 - piston lock screws 1....
Removal and installation of the pressure regulator You will need a key "on 10". The pressure regulator prevents the rear wheels from locking before the front wheels lock. This allows you to make the most of the braking...
Pressure Regulator Repair You will need a key "at 22". Before starting work : Remove the pressure regulator from the vehicle and drain the brake fluid from it. If fluid leaks from under the plug, a partial...
Replacement of brake hoses You will need: a special key or "on 10", key "at 15". It is recommended to use a special wrench to tighten the brake pipe nuts. The brake hose must be flexible, without tears or...
Replacement of brake pipes You will need: a special key or "on 10", key "at 15". It is recommended to use a special wrench to tighten the brake pipe nuts. The replacement is shown on the example of a tube...
Replacing the parking brake cable You will need: keys "on 10", "at 13" screwdriver Before starting work : Remove the rear wheel brake pads. Attention! Replace the cable with a new one if you find that the threads...
Parking brake lever repair You will need: key "on 10" screwdriver If the parking brake lever does not lock in the selected position, check the pawl spring first. If the spring is good, replace the lever....
Parking brake adjustment Stretching device (located under the bottom of the vehicle above the 1st stage muffler): 1 - equalizer; 2 - thrust; 3 - adjusting nut; 4 - cables; 5 - locknut Before adjusting the...
Adjustment of clearances between pads and brake drum You will need: balloon wrench two keys "at 13" screwdriver jack stand wheel chocks Loosen the parking brake cable tensioner nut ( see subsection 7.4.3. ). Remove the wheel. As the...