Brake system of cars VAZ-2110

All articles about the device and repair of units and elements of the brake system of VAZ-2110 (Lada 110) cars and their modifications.

Brake system — device and description
VAZ 2110 cars are equipped with two braking systems - service and parking. Service brake system it is designed to reduce the speed of the vehicle, even to the point of bringing it...

Checking the brake fluid level in the master cylinder reservoir
Warning: Before starting any repair work on your vehicle, be sure to read the safety instructions for working with brake fluid. The brake fluid level is checked periodically...

Bleeding brakes, replacing brake fluid
Bleeding the brakes is recommended after repairing the brake system that has caused a breach in the tightness of the system and if there is a suspicion of air entering the brake...

Brake pedal free play — checking and adjusting
Free travel of the brake pedal is the pedal travel from its upper position to the start of the brake mechanisms operation. It should be 3-5 mm. Adjusting the brake pedal 1....

Front brake mechanism — device and description
The cars are equipped with a front wheel brake mechanism, a ventilated disc, with a floating caliper and one working cylinder. The brake disc is cast iron, its minimum permissible...

Front Brake Pads — Checking Wear
Sequence of work to check the wear of the front brake pads: 1. Prepare the car for work (see points 1-3 " Preparing a car for maintenance and repair "). 2. Remove the front wheels...

Front brake pads — replacement
Below, brake pads without wear indicators are replaced. To replace brake pads with wear indicators, additionally disconnect the brake pad wire tip from the connector. To perform...

Front Brake Hose — Removal, Installation, Replacement
During each vehicle maintenance, visually inspect the condition of the brake hoses. Hoses that are worn, bulging, cracked or delaminating must be replaced immediately. Brake hoses...

Front Brake Caliper — Removal, Installation, Replacement
Removal 1. Prepare the car for repair work (see points 2b and 4 " Preparing a car for maintenance and repair "). 2. Remove the brake hose from the shock strut bracket (see point 3...

Front Caliper Brake Cylinder — Removal and Installation
To perform repair work on replacing the brake caliper cylinder, you will need a Torx T-16 socket wrench. Removal 1. Remove the brake caliper from the car (see " Front brake...

Front brake disc — removal, installation, replacement
Removal Warning: For safety reasons, it is recommended to replace brake discs in pairs, on both front brake mechanisms at once. Warning: The minimum thickness of a ventilated...

Brake Disc Protective Cover — Removal and Installation
Removal 1. Remove the brake disc (see " Brake disc - removal, installation, replacement "). 2. Using a 10 mm socket wrench, unscrew the three bolts securing the brake disc...

Rear brake mechanism — device and description
On VAZ 2110 cars, the manufacturer installed a rear drum brake mechanism. When the brake pedal is pressed, the brake fluid from the main brake cylinder enters the working brake...

Rear Brake Pads — Checking Wear
To perform repair work to check the wear of the rear brake pads, you will need a flashlight. 1. Prepare the car for repair work (see points 2b and 4 " Preparing a car for...

Rear brake drum — removal and installation
Removal 1. Prepare the car for repair work (see points 2b and 4 " Preparing a car for maintenance and repair "). 2. Fully lower the handbrake lever. 3. Release the handbrake cable...

Rear brake pads — removal, installation, replacement
The rear brake pads must be replaced if the thickness of the lining of any of the brake pads has become less than 1.5 mm, and also if the lining has separated from the base of the...

Rear brake cylinder — removal, installation, replacement
We replace the rear brake cylinder when there is a brake fluid leak and when the piston(s) in the brake cylinder "sticks", as a result of which one or both pistons stop moving in...

Rear Brake Shield — Removal and Installation
To carry out repair work you will need: 8mm Allen key with extension; vice with soft pads. Removal 1. Remove the rear brake cylinder from the shield (see " Rear brake cylinder -...

Rear brake hose — removal, installation, replacement
To perform repair work on replacing the rear brake hose, you will need a special key for brake pipe fittings. Removal 1. Prepare the car for repair work (see points 2b and 4 "...

Master Brake Cylinder — Removal, Installation, Replacement
To carry out repair work on replacing the main brake cylinder, you will need a special 10 mm wrench for the brake pipe fittings. Removal 1. Prepare the car for repair work (see...

Vacuum brake booster — check
1. We are preparing the vehicle for repair work (see point 2a " Preparing a car for maintenance and repair "). 2. With the engine not running, press the brake pedal several times...

Vacuum brake booster — removal, installation, replacement
Removal 1. We are preparing the vehicle for repair work (see point 2a " Preparing a car for maintenance and repair "). 2. Remove the right one (see " Interior heater - removal,...

Brake pedal — removal and installation
Removal 1. Remove the brake booster (see " Vacuum brake booster - removal, installation, replacement "). 2. To maintain the previous brake pedal adjustment, use a marker to mark...

Rear brake pressure regulator — device
During sharp braking, the load on the front axle of the car increases and the load on the rear axle decreases. At the same time, the grip of the front wheels with the road...

Rear Brake Pressure Regulator — Adjustment
The need to adjust the brake pressure regulator arises after its replacement, replacement of the rear suspension springs, or when the rear wheel brakes are not working properly....

Rear Brake Pressure Regulator — Removal and Installation
To perform repair work on replacing the rear brake pressure regulator, you will need: special keys for brake pipe fittings. Removal 1. Prepare the car for repair work (see points...

Checking and adjusting the handbrake
During vehicle operation, due to wear of the rear brake pads and stretching of the drive cables, it is periodically necessary to adjust the stroke of the handbrake lever. The...

Handbrake cables — removal, installation, replacement
The need to replace the handbrake cables arises if the cables, as a result of corrosion, have lost the ability to move in the casing, have stretched out significantly, or have...

Handbrake lever — removal and installation
To perform repair work to remove the handbrake lever from the car, you will need an inspection pit or overpass. Removal 1. Prepare the car for the work of removing the handbrake...

This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

More articles from other manuals on VAZ cars:
➠ Chassis: Brake system VAZ-21011 (1974-1983)
➠ Chassis: Brake system VAZ-21051 (1979-2010)
➠ Chassis: Brake system VAZ-21214 (1994-2006)
➠ Chassis: Brake system VAZ-2107 (1982-2012)
➠ Chassis: Brake system VAZ-1111 (1988-1996)

Share with friends: