Electrical equipment and devices of cars VAZ-21061
Wiring diagram of VAZ-21061 cars produced in 1976-1987 Scheme of electrical equipment of cars VAZ-2106, VAZ-21061, VAZ-21063 of release 1976-1987. 1 - front lights; 2 - side direction indicators; 3 - storage battery; 4 - relay...
Wiring diagram of VAZ-21061 cars produced in 1988–2001 Interactive diagram of the electrical equipment of cars VAZ-2106, VAZ-21061, VAZ-21063, VAZ-21065 manufactured in 1988-2001. 1 - front lights; 2 - side direction indicators; 3 -...
Fuses Connection of power sources (battery, generator) and consumers is made on a single-wire circuit. The function of the second wire is performed by the body («weight»), to which...
Checking electrical circuits To measure electrical parameters, digital or analog (turnout) tester - voltmeter, ohmmeter and other devices combined in one case. Digital instruments have a low inertia, they are...
Layout of fuses in the block Layout of fuses in the block 1 - main fuse block; 2 - additional fuse box; F1–F16 - fuses (see table. Electrical circuits protected by fuses ).
Replacing fuses Using a screwdriver, remove the cover of the main unit. The fuses are installed between the spring terminals. The fuses with a rating of 8A have a black insulator, 16A - green....
Replacing the main and additional fuse boxes head «for 8» unscrew the two nuts securing the fuse box to the body... ...and remove the blocks. In order not to get confused, we immediately connect each disconnected wire to the...
Replacing the Battery Charge Lamp Relay The PC702 relay is fixed to the mudguard of the right side member in the engine compartment with two self-tapping screws. A tip is installed under one of the screws «masses»....
Replacing the headlight relay To turn on the headlights (near or far light) on the mudguard of the right side member in the engine compartment, two relays 90.3747 are installed. Previously, relays 113.3747...
Windshield Wiper Relay Replacement Windshield Wiper Relay (PC514) designed to provide intermittent operation. It is installed under the dashboard on the driver's side and attached to the body with two screws....
Ignition switch replacement Disconnect the negative terminal of the battery. Removing the steering column cover (see Replacing paddle shifters ). Remove the wire plugs from the ignition switch terminals...
Replacing the contact part of the ignition switch Removing the ignition switch (see Ignition switch replacement ). Prying off with a thin screwdriver, remove the retaining ring. We take out the contact part from the switch body....
Windshield Wiper Repair Scheme of switching on the cleaner and washer of the windshield 1 - washer motor; 2 – the switch of a cleaner and a washer of a windshield; 3 – the relay of a cleaner of a...
Replacing windshield washer nozzles It is difficult to remove the nozzle without damaging its latches. Therefore, we simply pull out the old nozzle with pliers, after removing the hose put on its fitting under the...
Replacing the electric windshield washer pump Remove the hose from the pump fitting. Remove the wire end from the outlet «» pump motor (The polarity is marked on the motor cover) and wire end «masses» from withdrawal «minus»....
Heater motor repair Scheme of switching on the heater electric motor 1 - heater electric motor; 2 - additional resistor; 3 - heater motor switch; 4 - fuse block; 5 - ignition switch; 6 - generator; 7...
Electric fan of the engine cooling system Scheme of switching on the electric motor of the fan of the engine cooling system 1 - sensor for turning on the electric motor; 2 - fan motor; 3 - the relay of inclusion of the...
Replacing the electric fan sensor Drain the coolant from the engine radiator (see Coolant replacement ). Remove the two plugs from the sensor leads. key «at 30» open the sensor.. ... and replace it, making sure...
Replacing the cooling fan motor Disconnect the two plugs. Disconnect the connecting block. We remove the two plugs from the terminals of the electric fan sensor. key «for 8» unscrew the two bolts securing the...
Control devices — general information The dashboard has a combination of instruments, including a speedometer (with total and daily mileage counter); tachometer; coolant temperature, oil pressure and fuel gauges;...
Coolant temperature gauge Coolant temperature gauge (type UK-193) works in conjunction with a TM-106 temperature sensor screwed into the cylinder head. The sensor has a thermistor (resistor that changes...
Fuel level indicator Fuel gauge (type UK-193) works in conjunction with the BM-150 sensor installed in the fuel tank. The sensor is made in the form of a nichrome wire rheostat. The moving contact of...
Oil pressure gauge Oil pressure gauge (type UK-194) works in conjunction with the MM-393A sensor installed on the cylinder block. The pointer has the same design as the fuel gauge. The MM-393A...
Speedometer and tachometer — check Speedometer Speedometer SP-193 with a mechanical drive, it can only be checked on a special stand. Tachometer The TX-193 pointer tachometer determines the engine crankshaft speed...
Replacing the switches on the instrument panel The switch can be removed from the shield by pulling it towards you by the key. If you can't remove the switch... ... prying with a screwdriver, we remove it together with the...
Removing the instrument cluster Removing the upper steering column cover (see Replacing paddle shifters ). We pierce the skin with an awl - there is a stamping in the necessary places on the dashboard. Through...
Removing the radio panel insert Use a screwdriver to pry off one edge of the insert... ...and take it off. We remove the plugs from the terminals of the signaling device of insufficient level of brake fluid or...
Replacing the cigarette lighter lamp Removing the radio panel insert (see Removing the radio panel insert ). The cigarette lighter housing is fixed to the panel from the inside. For clarity, we show the replacement...
Replacing the heater motor switch Using a screwdriver, remove the switch from the instrument panel. Having marked or remembered the order of connecting the wires, remove the plugs from the switch terminals. We...
Replacing the fuel gauge sensor Removing the plastic trim on the fuel tank (see Trunk upholstery replacement ). We disconnect two wires from the sensor terminals, having previously marked their location. Using a...
Replacing the coolant temperature gauge sensor The coolant temperature indicator sensor is installed in the cylinder head on the right side. We change the sensor on a cold engine. Draining the coolant (see Coolant replacement...