Electrical equipment and appliances VAZ-21213

All articles about the installation and repair of electrical equipment and instruments of VAZ-21213 Niva cars.

Wires and fuses
The electrical equipment is made according to a single-wire scheme - the negative terminals of the sources and consumers of electricity are connected to the "ground", which acts...

Electrical equipment diagram of VAZ-21213 cars
Fig. 7-1. Electrical equipment diagram of VAZ-21213 cars: 1 - left front light; 2 - headlights; 3 - left headlight washer motor; 4 - sound signal; 5 - electromagnetic valve of the...

Features of lighting and signaling devices
The headlight switching circuit is shown in Fig. 7-28. The low and high beam headlights are switched on using auxiliary relays 3 and 11. The control voltage is supplied to the...

Possible lighting faults, their causes and methods of elimination
Some headlights and taillights do not light Cause of malfunction Method of elimination 1. The fuses have blown. 1. Replace the fuses. 2. The lamp filaments have burned out. 2....

Headlight adjustment
The direction of the headlight beams should be such that the road in front of the car is well lit and oncoming drivers are not blinded when the low beams are turned on. The...

Replacing lamps
Headlights. To replace the lamp: remove decorative trim 4 ( fig. 7-31 ) the front of the body, having unscrewed the screws 5 of the fastening; loosen screws 3 securing the...

Headlight Hydraulic Corrector
The headlight corrector consists of a master cylinder mounted on the instrument panel, actuator cylinders mounted on the headlights, and connecting tubes. The cylinders and tubes...

Three-lever switch
The switch is secured with a clamp to the steering shaft bracket. Removing the switch is performed in the following order: remove the steering wheel; remove the two halves of the...

Direction indicator and hazard warning flasher relay
Relay-breaker 8 ( fig. 7-30 ) type 231.3747 is designed to receive an intermittent light signal of the direction indicators both in the direction indicator mode and in the hazard...

Headlight relay
To turn on the headlights, relays 3 and 11 are used ( fig. 7-28 ) type 113.3747-10, installed under the instrument panel on the left side. The same relays are also used to turn on...

Sound signal
The cars are equipped with a sound signal of type 20.3721. It is located in the engine compartment and is attached to the radiator frame panel amplifier. The circuit diagram for...

Windscreen wiper and washer
The windshield wiper consists of a gear motor (electric motor with gearbox), lever drive and levers with brushes. The circuit diagram for connecting the windshield wiper and...

Possible malfunctions of the wiper and washer, their causes and methods of elimination
The wiper motor does not work, the bimetallic fuse does not trip, and fuse 2 in the fuse box does not blow Cause of malfunction Method of elimination 1. The power wires of the...

Removal and installation the windshield wiper
Repair of the cleaner mainly consists of straightening the deformed parts of the lever drive or replacing them with new ones. It is recommended to replace a faulty gear motor with...

Disassembly, assembly and inspection of the wiper motor reducer
To disassemble the gear motor, unscrew the screws securing cover 1 (Fig. 7-35) of the gear motor and remove it together with panel 2. Then unscrew the screws securing cover 16 to...

Windshield wiper relay
The relay type RS-514 is used to obtain intermittent operation of the windshield wiper. It is installed under the instrument panel on the left side and is attached to the body...

Headlight cleaners and washers
Headlight cleaners consist of two (left and right execution) gear motors with levers and brushes. The levers and brushes stop in the lower parking position. To protect the gear...

Rear window wiper, washer and heater, cigarette lighter
The rear window wiper consists of a gear motor type 471.3730, a lever and a brush. The lever with the brush is laid to the right in the direction of the vehicle's movement. The...

Electric motor of the heater fan
Electric motor type ME-255 direct current with excitation from permanent magnets. The electric motor connection diagram is shown in Fig. 7-38. Fig. 7-38. Wiring diagram for the...

Possible malfunctions of the heater electric motor, their causes and methods of elimination
The electric motor does not work Cause of malfunction Method of elimination 1. The wires are damaged or the wire connections are oxidized. 1. Check and repair connections. Replace...

Features of the control devices
All the vehicle's control devices are combined into a cluster of devices. It includes: a speedometer with a trip meter, a coolant temperature indicator, a fuel gauge, a...

Possible malfunctions of control devices, their causes and methods of elimination
Temperature or fuel gauge not working Cause of malfunction Method of elimination 1. The device is damaged. 1. Replace the instrument or instrument cluster. 2. The device sensor is...

Removal and installation the instrument cluster
To remove the instrument cluster, do the following: open the hood and disconnect the wire from the negative terminal of the battery; remove the instrument panel shield by...

Disassembling and assembling the instrument cluster
To disassemble, remove the speedometer daily counter handle by pulling it towards you, and then the frame with the glass by releasing its lower edge from the retaining spring...

Methodology for troubleshooting devices
Coolant temperature gauge If the pointer is constantly at the beginning of the scale, then with the ignition on, disconnect the wire from the pointer sensor and, through a 20-50...

Checking the devices
Coolant temperature gauge The device operates together with the sensor installed in the cylinder head. With a sensor resistance of 700 Ohm, the pointer should be at the beginning...

Checking the sensors of control devices
Coolant Temperature Gauge Sensor The sensor contains a thermistor that changes its resistance depending on the coolant temperature. The data for checking the sensor is given in...

Carburetor electromagnetic valve control system
Checking the control unit A serviceable control unit 5 (Fig. 7-41) should switch off valve 6 when the crankshaft speed increases to 2100 min - 1 and switch on the valve when the...

Electrical equipment of the car VAZ-21215-10
Car anti-theft system The VAZ-21215-10 vehicle is equipped with an automobile anti-theft system (APS) of the APS-2R relay type, consisting of a control unit 1 (Fig. 9-37), a...

This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

More articles from other manuals on VAZ cars:
➠ Electrical equipment: Equipment and devices VAZ-2110 (1995-2007)
➠ Electrical equipment: Equipment and devices VAZ-2107 (1982-2012)
➠ Electrical equipment: Equipment and devices VAZ-1111 (1988-1996)
➠ Electrical equipment: Equipment and devices VAZ-21061 (1976-2006)
➠ Electrical equipment: Equipment and devices VAZ-21099 (1990-2004)

Share with friends: