Equipment and electrical appliances VAZ-2110

All articles about the installation and repair of electrical equipment and instruments of VAZ-2110 (Lada 110) cars and their modifications.

Electrical equipment — description and device
The electrical network of the VAZ 2110 car is single-wire, the second conductor is the "ground" - the car body and the power unit. The negative terminals of the sources and...

The design and description of the fuse and relay mounting block
Fuses and relays for switching on the vehicle's electrical equipment are installed in the mounting block. The fuse and relay mounting block is installed in the instrument panel on...

Replacing fuses and relays in the mounting block
Warning. Before replacing a fuse in the mounting block, it is necessary to determine and eliminate the cause of its burnout. To avoid failure of electrical equipment components,...

Removal and installation repair of the mounting block
Removal 1. Disconnect the wire terminal from the negative terminal of the battery. 2. Open the cover of the mounting block. 3. Using a Phillips screwdriver, unscrew the screw that...

Description of switches and toggles
Note: The location and purpose of the switches installed on the vehicle in the instrument panel and in the floor tunnel trim are shown in the chapter "Controls and Instruments"....

Removal and installation the ignition switch
To complete the job, you will need four special bolts with breakaway heads. Note: If you don't have special bolts, you can secure the new ignition switch using M6 threaded bolts...

Removal and installation steering column switches
Note: The steering column switches can be removed and installed either individually or as a complete assembly with a connector (the central part of the switches). Depending on the...

Removal and installation the switch on the instrument panel trim
Note: In the instrument panel trim, next to the switches, there are control lamps for the corresponding devices. Removal 1. Disconnect the wire terminal from the negative terminal...

Removal and installation the switch in the floor tunnel trim
Note. The number of switches installed in the floor tunnel trim depends on the vehicle configuration. The work is shown using the example of removing and installing the front seat...

Removal and installation the interior light switch
Note: To replace the interior light switch, you do not need to disconnect the battery, since when the switch wire is shorted to ground, only the interior light will light. Removal...

Removal and installation the reverse light switch
Removal 1. Disconnect the wire terminal from the negative terminal of the battery. 2. Remove the air filter housing. 3. Drain the oil from the gearbox. 4. Disconnect the wire...

Removal and installation the brake light switch
Removal 1. Disconnect the wire terminal from the negative terminal of the battery. 2. Disconnect the electrical connectors of the two wires from the switch terminals. 3. Using a...

Removal and installation the horn
Removal 1. Remove the radiator grille. 2. Disconnect the wiring harness connector from the horn. 3. Using a 13 mm socket wrench, unscrew the horn plate mounting nut. 4. Remove the...

Device of control and measuring instruments and sensors
All the vehicle's control and measuring instruments: speedometer, odometer, tachometer, fuel gauge are installed on the instrument panel. The main control lamps are also located...

Removal and installation the instrument panel shield
Removal 1. Disconnect the terminal from the negative terminal of the battery on the vehicle. 2. Move the steering wheel down. 3. Remove the instrument panel trim. 4. Using pliers,...

Replacing the bulbs on the instrument panel
Note: When searching for a faulty bulb, keep in mind that the instrument cluster is upside down. The location of the bulbs on the front side of the instrument cluster is shown in...

Removal and installation the clock and light indicator unit
Note. The clock is mounted in the opening of the central console on four spring clamps, located in pairs at the top and bottom of the clock case. On some cars, a trip computer is...

Removal and checking the coolant temperature gauge sensor
To carry out repair work you will need: multimeter in ohmmeter mode with a measurement range from 0.1 to 10 kOhm); thermometer with a range of at least 100°C; a small...

Replacing the engine oil pressure sensor
Removal 1. Remove the plastic decorative engine cover. 2. Remove the protective cover from the sensor. 3. Using a 21 mm socket wrench, unscrew the oil pressure sensor... ...and...

Checking and replacing the brake fluid level sensor
Note: It is more convenient to check the brake fluid level sensor with an assistant. Examination 1. Prepare the car for repair work. 2. Briefly turn the key in the ignition and...

Replacing the washer fluid level sensor
Note. The contacts of the washer fluid level sensor should be closed if there is less than one liter of fluid left in the washer reservoir. If the corresponding indicator in the...

The structure and description of the windshield wiper and windshield washer
The VAZ 2110 sedan is equipped with a windshield wiper only. The VAZ 2112 hatchback and VAZ 2111 station wagon are additionally equipped with a rear window wiper. The windshield...

Removal and installation the windshield wiper
Note: The latest models of cars have a modernized heater, which prevents the removal of the windshield wiper. To remove the windshield wiper from such a car, before performing the...

Windshield wiper repair
Recommendation: A faulty windshield wiper motor-reducer should be replaced as an assembly. Disassembly 1. Remove the windshield wiper from the car. Warning. If the wiper arms were...

Removal and installation the windshield washer pump
Removal 1. Prepare the car for repair work. 2. Remove the battery. Helpful advice: If there is a lot of antifreeze left in the washer reservoir, then in order to save money, you...

Removal and installation the windshield washer reservoir
Removal 1. Prepare the car for repair work. 2. On late production cars (in which the upper crossbar of the front panel has bends and additional shields above the headlights)...

Removal and installation the rear window washer reservoir and pump
Removal 1. Remove the washer reservoir from the car. 2. Lift the tank and disconnect the elastic tube from the electric pump. 3. If it is necessary to replace the electric pump,...

Removal and installation windshield washer nozzles
Removal 1. Remove the air intake grille. 2. Using a Phillips screwdriver, unscrew the 12 screws securing the air intake grille trim. 3. Remove the air intake grille cover. 4....

This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

More articles from other manuals on VAZ cars:
➠ Electrical equipment: Equipment and devices VAZ-2121 (1977-1994)
➠ Electrical equipment: Equipment and devices VAZ-2109 (1984-1997)
➠ Electrical equipment: Equipment and devices VAZ-2107 (1982-2012)
➠ Electrical equipment: Equipment and devices VAZ-21051 (1979-2010)
➠ Electrical equipment: Equipment and devices VAZ-2115 (1997-2012)

Share with friends: