Engine power system — design description 1 - front tube of the fuel line; 2 – fuel fine filter; 3 – the lever of manual pumping of the fuel pump; 4 - fuel pump; 5 - fuel hose; 6 – a hose of an air inlet of warm air; 7 -...
Replacing the air filter element key «on 10» unscrew the three nuts securing the filter cover... ...and take it off. We take out the filter element, remove dust and debris from the filter housing. We install a...
Fuel pump replacement Using a Phillips screwdriver, loosen the clamps of the inlet and outlet fuel hoses. Remove the hoses from the pump fittings. To prevent gasoline from leaking, we plug the hoses...
Fuel pump repair Clear (replace) strainer and diaphragms can be replaced without removing the pump from the motor. But for ease of operation, it is better to remove the fuel pump and disassemble...
Replacing the fuel tank and its hatch cover Before removing the tank, we recommend draining the fuel into the canister with a hose through the filler neck. Removing the fuel tank cover (see Trunk upholstery replacement )....
Carburetor «Ozone» — design description Carburetor diagram «Ozone» 1 - screw for adjusting the stroke of the inlet valve of the accelerator pump; 2 - carburetor cover; 3 - fuel jet of the transition system of the second...
Fuel filter cleaning key «at 19» unscrew the filter cap (air filter housing removed for clarity)... ...and take it out along with the filter. We wash the filter and plug in acetone and blow it with...
Replacement of the electromagnetic valve of system of idling Disconnect the wire end from the valve outlet (air filter housing removed for clarity). We supply 12V from the battery to the valve output («minus» batteries connected to the car...
Carburetor Drive Adjustment Removing the air filter housing (see Carburetor replacement ). We measure the center-to-center distance between the rod ends, which should be equal to 80 mm. If necessary, remove...
Carburetor Throttle Adjustment Carburetor Throttle Adjustment a - partial opening of the throttle valve of the first chamber; b - full opening of the throttle valves; 1 - lever on the axis of the throttle valve...
Carburetor Trigger Adjustment Carburetor starter 1 - air damper drive lever; 2 - air damper; 3 - thrust of the starting device; 4 - the rod of the starting device; 5 - adjusting screw; 6 - throttle valve of...
Adjusting the fuel level in the float chamber Removing the carburetor cover (see Carburetor repair ). Attention! Before adjusting, we check the reliability of the needle valve (see Carburetor repair ). Holding the lid upright...
Carburetor idle adjustment Scheme of the carburetor idle system 1 - throttle body; 2 - throttle valve of the first chamber; 3 - openings of transient modes; 4 - hole, adjustable screw amount of the mixture;...
Carburetor replacement After loosening the clamp, disconnect the corrugated warm air intake hose from the pipe. Removing the air filter (see Replacing the air filter element ). key «for 8» unscrew the...
Carburetor repair — general information Violations in the operation of the carburetor during the operation of the car are most often associated with clogging of its channels (calibrated holes of small diameter and fuel...
Carburetor Needle Valve Repair By compressing the spring of the telescopic thrust of the starting device,.. ... disconnect it from the three-arm choke lever. Using a Phillips screwdriver, unscrew the five...
Disassembly and inspection of carburetor cover parts Using a Phillips screwdriver, unscrew the two screws securing the housing of the starting device.. ... and remove the body and traction. Remove the rubber sealing ring. By...
Pneumatic throttle repair Prying with an awl, remove the retaining ring of the throttle actuator of the second chamber. Using a Phillips screwdriver, unscrew the two screws securing the pneumatic drive...
Disassembly and repair of the carburetor body Remove return spring. Using a Phillips screwdriver, unscrew the screw securing the three-arm lever.. ... and, holding it, remove the spring mounting bracket. We remove the lever...
Dismantling and repair of the throttle body Using a Phillips screwdriver, unscrew the two screws securing the sleeve.. ... and remove it together with the screw for adjusting the amount of mixture. We remove the gasket from...
Exhaust System — Design Description 1 - exhaust pipe; 2 – a pillow of a suspension bracket of an exhaust pipe; 3 – a belt of a suspension bracket of the muffler; 4 - main muffler; 5 - front pipe of the main muffler;...