Designation | Name |
A.40005 | Universal Puller Kit |
A.40006 | Puller (ejector) front bearing of the input shaft of the gearbox |
A.40009 | Stud wrench |
A.40026 | Coolant pump impeller puller |
A.45008 | Tool for removing the inner ring of the rear bearing of the final drive gear |
A.45028 | Emphasis for removing the inner rings of the bearings of the differential box |
A.47035 | Puller of ball pins of steering rods from the holes of the bipod and pendulum lever |
A.47043 | Steering arm puller |
A.47046 | Device for pressing out and pressing in rubber-metal hinges of the upper arms of the front suspension |
A.47052 | Steering link ball pin puller |
A.50088 | Nut wrench for intake and exhaust pipes |
A.50113 | Wrench for oil release plug from the engine crankcase |
A.50121 | Crankshaft ratchet wrench |
A.50126 | Wrench to control the tightening torque of the cylinder head bolts (with installed camshaft) |
A.55035 | Spanner for removing and installing gearbox |
A.55085 | Differential box bearing wrench |
A.56122 | Wrench for adjusting rear wheel brakes |
A.56124 | Wrench for rear brake pressure regulator plug |
A.57034/R | Shock Reservoir Nut Wrench |
A.57070 | Wrench for removing and installing front shock absorbers |
A.60018 | Spark Plug Fitting Plug for Valve Leak Testing |
A.60153/R | Mandrel for pressing in and out of the guide bushings of the intake and exhaust valves |
A.60308 | Piston pin press tool |
A.60311/R | Tool for removing and installing engine valves |
A.60312 | Oil Filter Remover |
A.60325 | Device for hot pressing the piston pin into the piston and connecting rod |
A.60326/R | Mandrel for pressing out of the cylinder block of the bushing of the gear of the oil pump drive and the ignition distributor |
A.60330/R | Flywheel retainer when it is installed on the crankshaft |
А.60333/1/2 | Mandrel for pressing in and pressing out bushings of the oil pump drive shaft |
A.60334 | Cylinder head leak test tool |
A.60335 | Cylinder head plate used when removing and installing valves |
A.60353 | Cylinder head support for valve seat repair |
A.60430 | Coolant pump impeller installer |
A.60604 | Set of sleeves for installation in piston cylinders (normal and oversized |
A.70017 | Tool for removing and installing clutch pedal springs |
A.70025 | Clamp for removing and installing the flexible coupling of the cardan shaft |
A.70045 | Mandrel for pressing the intermediate support bearing |
A.70081 | Drift for centering clutch disc |
A.70152 | Mandrel for pressing the inner ring of the rear bearing onto the final drive gear |
A.70157 | Mandrel for installing the axle shaft seal |
A.70171 | Mandrel for pressing the outer ring of the rear bearing of the final drive pinion |
A.70172 | A pair of flanges for installation at the ends of the rear axle beam when checking it |
A.70184 | A device for determining the thickness of the gaskets when adjusting the clearance in the meshing of the final drive gears |
A.70185 | Mandrel for pressing the outer ring of the front bearing of the final drive pinion |
A.70198 | Mandrel for pressing out the outer rings of the main gear drive gear bearings |
A.70526 | Traverse for supporting the engine with gearbox |
A.72236 | Device for locking the pistons of the working cylinder of the rear brakes |
A.74035 | Mandrel for installing the intermediate support on the cardan shaft |
А.74076/1 | Steering gear housing repair tool |
A.74076/R | Bracket for fastening the housing of the steering mechanism, attached to the device A.74076/1 |
A.74088 | Mandrel for installing front wheel hub caps |
A.74105 | Mandrel for pressing in and pressing out bushings of the shaft of the bipod of the steering mechanism |
A.74107/R | Parts for pressing the bearing and the locking ring of the axle shaft |
A.74108/R | Device for pressing out the bearing and locking ring from the axle shaft |
A.74155/R | Mandrel for installing the outer ring of the inner and outer bearings of the front wheels |
А.74177/2 | Device for installing rubber-metal hinges on the lower arm of the front suspension |
A.74186 | Spacer used with tool A.74177/1 |
А.74177/1 | Mandrel for pressing the outer rings of the bearing of the worm shaft of the steering gear |
A.76027 | Valve punch |
A.76028 | Valve punch |
A.76029 | Support for pressing valves |
A.76031 | Support for pressing valves |
A.76032 | Base plate for pressing valves |
A.76034 | Tool for removing the locking clip of the power window handle |
A.78124/R | Front Suspension Crossmember Test Tool |
A.86010 | Drift for pressing crankshaft plugs |
A.86606 | Wrench for screwing M6x1 studs |
A.86608 | Wrench for screwing pins M8x1.25 |
A.86610 | Wrench for screwing studs M10x1.25 |
A.90310 | A set of reamers for processing holes in the valve guide bushings |
A.90336 | Reamer for processing bushings of the steering gear housing |
A.90353 | Reamer for oil pump drive shaft bushings, ignition distributor and fuel pump |
A.94003 | Countersink for processing inlet valve seats |
A.94016 | Countersink spindle for processing plug sockets |
А.94016/10 | Countersink for machining sockets of crankshaft plugs |
A.94031 | Countersink (20°) for machining exhaust valve seats |
A.94058 | Countersink spindle for machining valve seats |
A.94059 | Set of guide rods for machining valve seats |
A.94069 | Spindle for grinding wheel for valve seat machining |
A.94078 | Grinding wheel for inlet valve seats |
A.94092 | Countersink for machining exhaust valve seats |
A.94100 | Grinding wheel for inlet valve seats |
A.94101 | Countersink (20°) for machining intake valve seats |
A.95111 | Feeler gauge for checking the clearance between the lever and the camshaft cam |
A.95601/R | Device for checking the reliability of pressing the locking ring on the axle shaft |
A.95615 | Device for checking the reliability of pressing the piston pin |
A.95688/R | A device for adjusting the clearance in the engagement of the drive and driven gears of the final drive and tightening the differential nuts |
A.95690 | Device for determining the thickness of the adjusting ring of the drive gear |
A.95697/5 | Head for dynamometer 02.7812.9501 |
A.95716 | Front suspension arm tester with ball joints |
A.96008 | Gauge for steering knuckle control |
A.96137 | Ring gauge for inside gauge installation |
02.7812.9500 | 13 mm socket wrench for removing and installing the starter and muffler downpipe |
02.7823.9501 | Dynamometer for monitoring the rolling moment of the bearings of the drive gear of the rear axle gearbox and the shaft of the worm of the steering gear |
02.7823.950 | Device for pressing out the hinges of the lower arms of the front suspension (without removing levers) |
02.7823.9501 | Device for pressing the hinges of the lower arms of the front suspension (without removing levers) |
02.7823-9604 | Alternator Pulley Remover |
02.7823.9505 | Tool for removing and installing engine valves (can be used instead of the portable device A.60311/R |
02.7834.9504 | A device for measuring the axial free play of the axle shaft |
02.7834.9505 | Device for measuring the axial clearance of the front wheel hub bearings |
02.8701.9500 | Device for measuring the gap in the upper hinge of the front suspension |
02.8701.9502 | Tool for checking the condition of the front suspension ball joint (removed from the vehicle) |
41.7816.4013 | socket wrench (21 mm) for tightening the guide adjusting bolts of the valve levers |
41.7816.4068 | Transmission input shaft retainer |
41.7816.4069 | Device for installing the retaining ring on the secondary shaft of the gearbox |
41.7820.4003 | Drift for centering the oil pump shaft when installed on the engine |
41.7820.4006 | Device for installing the driven gear of the oil pump drive and ignition distributor |
41.7834.4092 | Caliber for selection of universal joint retaining rings |
41.7853.4010 | Mandrel for installing the camshaft drive cover on the engine |
41.7853.4011 | Mandrel for fitting the gland holder (with stuffing box) on the crankshaft |
41.7853.4016 | Mandrel for installing valve guide valve stem seals |
41.7853.4028 | Mandrel for installing the bearing of the secondary shaft of the gearbox |
41.7853.4032 | Mandrel for installing the bearing of the intermediate shaft of the gearbox |
41.7853.4039 | Mandrel for installation of an epiploon of a secondary shaft of a transmission |
67.7141.9500 | Mandrel for turning the disc of the front brake |
67.7801.9513 | Device for pressing out the ball pins of the front suspension joints |
67.7801.9514 | Front wheel hub cap remover |
67.7801.9516 | Rear axle shaft puller |
67.7812.9513 | Dynamometer to control the tension of the fan drive belt |
67.7812.9514 | Wrench for removing and installing spark plugs |
67.7812.9515 | Wrench for controlling the tightening torque of spark plugs |
67.7812.9517 | Hinged extension L=500 mm |
67.7812.9518 | Hinged extension L=1000 mm |
67.7812.9519 | Socket for removing and installing spark plugs |
67.7813.9503 | Clutch Drive Repair Tool |
67.7813.9504 | Tie Rod Clutch Wrench |
67.7820.9517 | Set of devices for replacing bushings of the rear suspension rods |
67.7820.9518 | A device for monitoring the installation of the rear brake pressure regulator when «X» =140±5 mm(see fig.6-4) |
67.7822.9512 | car stand |
67.7822.9517 | Jig for replacing clutch disc linings |
67.7823.9522 | Clamp for replacing the propeller shaft crosspieces |
67.7824.9513 | Shock Absorber Repair Kit |
67.7824.9521 | Chain stretcher |
67.7828.9504 | Front Suspension Spring Compressor |
67.7834.9506 | Tool for measuring the protrusion of the pusher of the fuel pump |
67.7851.9500 | Mandrel for riveting clutch disc |
67.7853.9525 | Mandrel for pressing the front wheel hub seal |
67.7853.9526 | Washer for pressing out the outer ring of the inner bearing of the front wheel hub |
67.7853.9527 | Mandrel for pressing the outer ring of the outer bearing of the front wheel hub |
67.7853.9541 | Mandrel for pressing out the outer ring of the upper bearing of the steering gear worm |
67.7853.9543 | Mandrel for compressing the spring of the brake master cylinder when installing the locking screws |
67.8151.9505 | Caliber for monitoring the fuel level in the carburetor |
67.8701.9510 | Device for measuring the axial clearance of the crankshaft |
67.8720.9501 | Steering wheel free play control device |
TCO–3/379 | Traverse for removal and installation of the engine |
BS–106.000 | Stand for testing thermostats |
* Tool kits supplied to the customer are determined by separate lists.