Engine
Designation | Name |
A.40005 | Universal Puller Kit |
A.40026 | Coolant pump impeller puller |
A.50088 | Nut wrench for intake manifold and exhaust manifold |
A.50113 | Wrench for oil release plug from the engine crankcase |
A.50121 | Ratchet wrench (nuts) crankshaft |
A.50126 | Wrench to control the tightening torque of the cylinder head bolts (with installed camshaft) |
A.60153/R | Mandrel for pressing in and out of the engine valve guide bushings |
A.60308 | Piston pin press tool |
A.60311/R | Valve removal and installation tool |
A.60312 | Oil Filter Remover |
A.60312 | Piston pin tool for 2101 and 2103 engines |
A.60326/R | Mandrel for pressing out of the cylinder block of the bushing of the gear of the oil pump drive and the ignition distributor |
A.60330/R | Flywheel retainer when installing it on the crankshaft |
A.60333/1/2 | Mandrel for pressing in and pressing out bushings of the oil pump drive shaft |
A.60334 | Cylinder head leak test tool |
A.60335 | Cylinder head board used when removing and installing valves |
A.60353 | Cylinder head support for valve seat repair |
A.60430 | Coolant pump impeller installer |
A.60604 | Set of sleeves for installation in piston cylinders of engines 2101 and 2103 |
A.86010 | Drift for pressing crankshaft plugs |
A.90310 | A set of reamers for processing holes in the valve guide bushings |
A.90353 | Reamer for oil pump drive shaft bushings, ignition distributor and fuel pump |
A.94003 | Countersink for processing inlet valve seats |
A.94016 | Countersink spindle for processing plug sockets |
А.94016/10 | Countersink for machining sockets of crankshaft plugs |
A.94031 | Countersink (20°) for machining exhaust valve seats |
A.94058 | Countersink spindle for machining valve seats |
A.94059 | Set of guide rods for machining valve seats |
A.94069 | Spindle for grinding wheel for valve seat machining |
A.94078 | Grinding wheel for processing exhaust valve seats |
A.94092 | Countersink for machining exhaust valve seats |
A.94100 | Grinding wheel for inlet valve seats |
A.94101 | Countersink (20°) for machining intake valve seats |
A.95111 | Feeler gauge for checking the clearance between the lever and the camshaft cam |
A.95615 | Device for checking the reliability of pressing the piston pin |
A.96137 | Ring gauge for setting the bore gauge to zero when checking engine cylinders 2101 and 2103 |
02.7812.9500 | Socket wrench (S=13 mm) for removing and installing the starter and downpipe mufflers |
02.7853.9500 | Piston pin press tool |
02.7854.9500 | Set of sleeves for installation in piston cylinders |
41.7816.4013 | socket wrench (S=21mm) for tightening the bushings of the adjusting bolts of the valve actuator levers |
41.7820.4003 | Drift for centering the oil pump shaft when installed on the engine |
41.7820.4006 | Device for installing the driven gear of the oil pump drive and ignition distributor |
41.7853.4010 | Mandrel for installing the camshaft drive cover on the engine |
41.7853.4011 | Mandrel for fitting the gland holder (with stuffing box) on the crankshaft |
41.7853.4016 | Mandrel for installing valve guide valve stem seals |
67.7811.9508 | Key for cranking the crankshaft of the engine |
67.7812.9514 | Wrench for removing and installing spark plugs |
67.7812.9515 | Wrench for controlling the tightening torque of spark plugs |
67.7812.9519 | Socket for removing and installing spark plugs |
67.7824.9521 | Chain draw tool |
67.7834.9506 | Tool for measuring the protrusion of the pusher of the fuel pump |
67.7853.9548 | Drift for centering the cover of the camshaft drive of the engine 2105 |
67.7853.9549 | Drift for centering the holder of the front oil seal of the crankshaft of the engine 2105 |
67.8125.9501 | Ring gauge for setting the inside gauge to zero when measuring engine cylinders 2105 |
67.8151.9505 | Caliber for monitoring the fuel level in the carburetor |
67.8701.9510 | Device for measuring the axial clearance of the crankshaft |
ТСО-3/379 | Traverse for removal and installation of the engine |
BS-106 | Stand for testing thermostats |
Clutch
A.70017 | Tool for removing and installing clutch pedal springs |
67.7813.9503 | Clutch Drive Repair Tool |
67.7822.9517 | Conductor for replacement of pads of the driven disk |
67.7851.9500 | Mandrel for riveting the driven disk |
A.70081 | Mandrel for centering the driven disk |
Transmission
A.40006 | The ejector of the forward bearing of a primary shaft of a transmission |
A.55035 | Spanner for removing and installing gearbox |
A.55085 | Wrench for differential bearing nuts |
41.7816.4068 | Transmission input shaft retainer |
41.7816.4069 | Installer (withdrawals) retaining ring on the secondary shaft of the gearbox |
41.7853.4028 | Mandrel for installation of the bearing of a secondary shaft |
41.7853.4032 | Mandrel for installing the bearing of the intermediate shaft |
41.7853.4039 | Mandrel for installation of an epiploon of a secondary shaft |
Cardan gear
A.70025 | Clamp for removing and installing the flexible coupling of the cardan shaft |
A.70045 | Mandrel for pressing the intermediate support bearing |
A.74035 | Mandrel for pressing the intermediate bearing onto the cardan shaft |
41.7834.4092 | Caliber for selection of retaining rings of bearings of universal joint cross |
67.7823.9522 | Clamp for replacing universal joint crosses |
Rear axle
A.45008 | Tool for removing the inner ring of the rear bearing of the final drive gear |
A.45028 | Emphasis for removing the inner rings of the bearings of the differential box |
A.70152 | Mandrel for pressing the inner ring of the rear bearing onto the drive gear |
A.70157 | Mandrel for installing the axle shaft seal |
A.70171 | Mandrel for pressing the outer ring of the rear bearing of the final drive pinion |
A.70172 | A pair of flanges for installation at the ends of the rear axle beam when checking it (editing) |
A.70184 | A device for determining the thickness of the gaskets when adjusting the clearance in the meshing of the final drive gears |
A.70185 | Mandrel for pressing the outer ring of the front bearing of the final drive pinion |
A.70198 | Mandrel for pressing out the outer rings of the main gear drive gear bearings |
A.74107/R | Parts for pressing the bearing and the locking ring of the axle shaft |
A.74108/R | Device for pressing out the bearing and locking ring from the axle shaft |
A.95601/R | Device for checking the reliability of pressing the locking ring on the axle shaft |
A.95688/R | A device for adjusting the clearance in the engagement of the drive and driven gears of the final drive and tightening the nuts of the differential bearings |
A.95690 | Tool for determining the thickness of the drive gear shim |
A.95697/5 | Head for dynamometer 02.7812.9501 |
02.7812.9501 | Dynamometer to control the moment of resistance to turning the drive gear of the rear axle gearbox and the shaft of the worm of the steering gear |
02.7834.9504 | A device for measuring the axial free play of the axle shaft |
67.7801.9516 | Rear axle shaft puller |
A.47035 | Tie rod ball pin puller from bipod hole and pendulum arm |
A.47043 | Steering arm puller |
A.47052 | Steering link ball pin puller |
А.74076/1 | Steering gear housing repair tool |
A.74076/R | Bracket for fastening the housing of the steering mechanism, attached to the device A.74076/1 |
A.7405 | Mandrel for pressing in and pressing out bushings of the shaft of the bipod of the steering mechanism |
A.74186 | Mandrel for pressing the outer rings of the worm shaft bearing |
A.90336 | Reamer for processing bushings of the steering gear housing |
67.7813.9504 | Tie Rod Clutch Key |
67.7853.9541 | Mandrel for pressing out (press fittings) worm upper bearing outer ring |
67.8720.9501 | Steering wheel free play control device |
Front suspension
A.47046 | Device for pressing out and pressing in rubber-metal hinges of the upper arms |
A.57034/R | Wrench for shock absorber nut |
A.57070 | Wrench for removing and installing front shock absorbers |
A.70526 | Traverse for supporting the engine with gearbox |
A.74088 | Mandrel for installing front wheel hub caps |
A.74155 | Mandrel for installing the outer ring of the inner and outer bearings of the front wheels |
А.74177/1 | Device for installing rubber-metal hinges on the lower suspension arm |
А.74177/2 | Spacer sleeve used with tool A.74177/1 |
A.78124/R | Front Suspension Crossmember Test Tool |
A.95716 | Front suspension arm tester with ball joints |
A.96008 | Gauge for steering knuckle control |
02.7823.9500 | Device for pressing out the hinges of the lower arms of the front suspension (without removing levers) |
02.7823.9501 | Device for pressing the hinges of the lower arms of the front suspension (without removing levers) |
02.7834.9505 | Device for measuring the axial clearance of the front wheel hub bearings |
02.8701.9500 | Upper ball joint clearance gauge |
02.8701.9502 | Ball Joint Check Tool (taken from the car) |
67.7801.9513 | Device for pressing out the ball pins of the suspension joints |
67.7801.9514 | Front wheel hub cap remover |
67.7824.9513 | Shock Absorber Repair Kit |
67.7828.9504 | Suspension Spring Compressor |
67.7853.9504 | Wrench for adjusting the convergence of the front wheels |
67.7853.9525 | Mandrel for pressing the front wheel hub seal |
67.7853.9526 | Washer for pressing out the outer ring of the inner bearing of the front wheel hub |
67.7853.9527 | Mandrel for pressing the outer ring of the outer bearing of the front wheel hub |
Rear suspension
67.7820.9517 | Set of devices for replacing bushings of the rear suspension rods |
Brakes
A.56124 | Wrench for rear brake pressure regulator plug |
67.7141.9500 | Mandrel for turning the disc of the front brake |
67.7820.9518 | Device for control of installation of a regulator of pressure of back brakes |
Electrical equipment
02.7823.9504 | Alternator Pulley Remover |
Tool kits supplied to the customer are defined by separate lists.