Doors and windows of cars VAZ-21051 «Zhiguli»

Removal and installation doors
Removal 1. Knock out the limiter mounting pin 3 and disconnect the limiter from the rack. 2. While holding the door in the open position, use an impact screwdriver to unscrew 2...

Disassembling the front doors
View of the inside of the front door 1 – window plug; 2 – window lift handle; 3 – internal handle of the lock drive; 4 – armrest handle; 5 – decorative plug; 6 – door lock button....

Assembly of front doors
1. Assemble the front doors in the reverse order of disassembly. 2. When installing the window lift, check that the cable is positioned correctly on the drum; the cable turns...

Disassembly and assembly of rear doors
Rear window drive 1 – window lift handle; 2 – handle lining; 3 – window lift mechanism; 4 – roller; 5 – pressure plate; 6 – screw; 7 – tension roller The operations for...

Adjusting the door position
1. Before adjusting, outline the contours of the loops 4 (see Fig subsection 10.2 ) on the body pillar. 2. Using impact screwdriver 2, loosen screws 1 securing the hinges. 3. Move...

Adjusting door locks
1. For proper operation of the door lock, adjust the position of the housing 15 (see Fig. Front left door lock ) of the lock retainer, after loosening the mounting bolts. 2. If...

Adjusting the stroke of the lowering glass
Front doors 1. Remove the trim from the front doors, lower the glass until it stops against the rubber buffer and unscrew screws 6 (see Fig. Front window drive ) pressure plates...

Removal, installation and adjustment of the trunk lid
Trunk lid 1 – lock; 2 – trunk lid; 3 – nut; 4 – loop; 5 – seal; 6 – retainer; 7 – torsion bar Trunk lock 1 – rotor axis; 2 – lock body cover; 3 – lock drive extension; 4 – lever;...

Windshield replacement
Windshield with seal assembly 1 – stamping for water drainage; 2 – edging trim of the seal; 3 – seal edging; 4 – glass; 5 – seal; 6 – windshield opening flange 1. To remove the...

Rear window replacement
1. To remove the glass, remove the seal edging and, pressing on the lower corners of the glass, push it out. At the same time, an assistant should support the glass from the...

Removal and installation the windshield washer pump
Windshield and headlight washer circuit diagram 1 – headlight washer jets; 2 – check valves; 3 – feed tank; 4 – headlight washer pressure pump; 5 – windshield washer jets; 6 -...

Windshield washer pressure pump
Disassembly 1. Pressure pump and electric motor 1 (see Fig. Windshield washer pressure pump ) are fastened with screws and nuts to cover 2. 2. To disassemble the pump, unscrew the...

Removal and installation windshield washer jets
Windshield washer jet 1 – sprayer; 2 – screw; 3 – bushing; 4 – jet body with fitting 1. If the jets are clogged, remove and disassemble them. 2. From the air intake box side of...

Removal and installation of pipes, tees
The washer tubes are located together with the electrical wire bundles. 1. When removing tubes from nozzles, tees, and pumps, care must be taken. 2. Remove and install the tubes...

This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

More articles from other manuals on VAZ cars:
➠ Body: Doors, covers and windows VAZ-21214 (1994-2006)
➠ Body: Doors and glass VAZ-2110 (1995-2007)
➠ Body: Doors and glass VAZ-2107 (1982-2012)
➠ Body: Doors and locks VAZ-21011 (1974-1983)
➠ Body: Doors and locks VAZ-11113 (1996-2003)

Share with friends: