Designation | Name |
Engine | |
A.40005 | Universal Puller Kit |
A.40026 | Coolant pump impeller puller |
A.50088 | Nut wrench for intake and exhaust pipes |
A.50113 | Wrench for oil release plug from the engine crankcase |
A.50121 | Wrench for crankshaft pulley bolt |
A.50126 | Wrench to control the tightening torque of the cylinder head bolts (with installed camshaft) |
A.60153/R | Mandrel for pressing in and out of the guide bushings of the intake and exhaust valves |
A.60311/R | Tool for removing and installing engine valves |
A.60312 | Oil Filter Remover |
A.60326/R | Mandrel for pressing out of the cylinder block of the bushing of the gear of the oil pump drive and the ignition distributor |
A.60330/R | Flywheel retainer when it is installed on the crankshaft of the engine |
А.60333/1/2 | Mandrel for pressing in and pressing out bushings of the oil pump drive shaft |
A.60334 | Cylinder head leak test tool |
A.60430 | Coolant pump impeller installer |
A.86010 | Drift for pressing crankshaft plugs |
A.90310 | A set of reamers for processing holes in the valve guide bushings |
A.90353 | Reamer for oil pump drive shaft bushings, ignition distributor and fuel pump |
A.94003 | Countersink (75s) for machining intake valve seats |
A.94016 | Countersink spindle for plug processing |
А.94016/10 | Countersink for machining sockets of crankshaft plugs |
A.94031 | Countersink (20s) for machining exhaust valve seats |
A.94058 | Countersink spindle for machining valve seats |
A.94059 | Set of guide rods for machining valve seats |
A.94069 | Spindle for grinding wheel for valve seat machining |
A.94078 | Grinding wheel for processing exhaust valve seats |
A.94092 | Countersink for machining exhaust valve seats |
A.94100 | Grinding wheel for inlet valve seats |
A.94101 | Countersink (20s) for machining intake and exhaust valve seats |
A.95111 | Feeler gauge for checking the clearance between the lever and the camshaft cam |
02.7812.9500 | 13 mm socket wrench for removing and installing the starter and muffler downpipe |
02.7823.9505 | Valve removal and installation tool (can be used instead of A.60311/R) |
41.7816.4013 | socket wrench (21 mm) for tightening the guide adjusting bolts of the valve levers |
41.7853.4010 | Mandrel for installing the camshaft drive cover on the engine |
41.7853.4011 | Mandrel for fitting the gland holder (with stuffing box) on the crankshaft |
41.7853.4016 | Mandrel for installing valve guide valve stem seals |
67.7812.9513 | Dynamometer to control the tension of the fan belt |
67.7812.9514 | Wrench for removing and installing spark plugs |
67.7812.9515 | Wrench for controlling the tightening torque of spark plugs |
67.7812.9519 | Socket for removing and installing spark plugs |
67.7824.9521 | Wear Check Tool (hoods) camshaft drive chain |
67.7834.9506 | Tool for measuring the protrusion of the pusher of the fuel pump |
67.7854.9519 | Adjustable sleeve to fit normal and oversized pistons with a diameter of 82 mm |
67.8125.9502 | Ring gauge, 82 mm in diameter, for setting the inside gauge to zero |
67.8151.9505 | Caliber for monitoring the fuel level in the carburetor |
TOO-3/379 | Traverse for removal and installation of the engine |
BS-106 | Stand for testing thermostats |
Clutch | |
A.70017 | Tool for removing and installing clutch pedal springs |
A.70081 | Drift for centering clutch disc |
67.7813.9503 | Clutch Drive Repair Tool |
67.7822.9517 | Conductor for replacement of pads of the driven disk |
67.7851:9500 | Mandrel for riveting linings of the driven disk |
Transmission | |
A.40006 | Input shaft front bearing ejector |
A.55035 | Key with joint for installing and removing the gearbox |
41.7816.4068 | Transmission input shaft retainer |
41.7816.4069 | Installer (withdrawals) retaining ring on the secondary shaft of the gearbox |
41.7853.4028 | Mandrel for installation of the bearing of a secondary shaft |
41.7853.4032 | Mandrel for installing the bearing of the intermediate shaft |
41.7853.4039 | Mandrel for installation of an epiploon of a secondary shaft |
67.7853.9558 | Mandrel for pressing the bearing of the differential of the transfer case |
cardan gear | |
A.70025 | Clamp for removing and installing flexible coupling |
41.8734.4092 | Caliber for selection of retaining rings of bearings of the universal joint shaft |
67.7823.9522 | Clamp for replacing universal joint crosses |
67.7853.9533 | Mandrel for pressing the ring of the epiploon of the hinge of the drive of the front wheels |
67.7853.9537 | Mandrel for installation of protective covers of hinges of a drive of forward wheels |
Drive axles | |
A.45008 | Tool for removing the inner ring of the rear bearing of the final drive gear |
A.45028 | Emphasis for removing the inner rings of the bearings of the differential box |
A.55085 | Wrench for differential bearing nuts |
A.70152 | Mandrel for pressing the inner ring of the rear bearing onto the drive gear |
A.70157 | Mandrel for installing the axle shaft seal |
A.70171 | Mandrel for pressing the outer ring of the rear bearing of the final drive pinion |
A.70172 | A pair of flanges for installation at the ends of the rear axle beam when checking it (editing) |
A.70184 | A device for determining the thickness of the gaskets when adjusting the clearance in the meshing of the final drive gears |
A.70185 | Mandrel for pressing the outer ring of the front bearing of the final drive pinion |
A.70198 | Mandrel for pressing out the outer rings of the main gear drive gear bearings |
67.7823.9530 | Tool for installing the locking ring of the axle shaft |
67.7823.9529 | Tool for removing the locking ring from the axle shaft |
A.95601/R | Device for checking the reliability of pressing the locking ring on the axle shaft |
A.95688/R | A device for adjusting the clearance in the engagement of the drive and driven gears of the final drive and tightening the nuts of the differential bearings |
A.95690 | Tool for determining the thickness of the drive gear shim |
A.95697/5 | Head for dynamometer 02.7812.9501 |
02.7812.9501 | Dynamometer to control the moment of resistance to turning the drive gear of the drive axle reducer and the shaft of the worm of the steering gear |
67.7812.9520 | Wrench for adjusting the front axle gearbox |
02.7834.9504 | A device for measuring the axial free play of the axle shaft |
67.7823.9516 | Rear axle shaft puller |
67.7853.9559 | Stop for removing differential bearing |
67.8701.9508 | Bracket with tip for A.95688/R tool for adjusting the front axle reduction |
Front suspension | |
A.47045 | Device for pressing rubber-metal hinges of the upper suspension arms |
A.57034/R | Shock Reservoir Nut Wrench |
A.57070 | Wrench for removing and installing front shock absorbers |
А.74177/1 | Device for installing rubber-metal hinges on the upper arm of the front suspension (applies from 67.7853.9519) |
02.8701.9502 | Device for checking the condition of the ball joints of the front suspension |
67.7820.9514 | Traverse for hanging the engine |
67.7820.9520 | Mandrel for crimping nuts |
67.7820.9521 | Lever for moving the front wheel hub when checking the clearance in the bearings |
67.7823.9514 | Wheel hub cap remover |
67.7823.9515 | Lower arm axle ejector |
67.7823.9517 | Device for pressing out and pressing in rubber-metal hinges of the lower suspension arm |
67.7823.9526 | Device for pressing in and out of rubber-metal hinges of the lower suspension arm on the press |
67.7823.9527 | Device used for pressing rubber-metal hinges of the upper suspension arm |
67.7824.9513 | Shock Absorber Repair Kit |
67.7834.9507 | Front wheel bearing clearance gauge |
67.7853.9519 | Device for pressing in the rubber-metal hinge of the upper suspension arm (used with tool A.74177/1) |
67.7853.9528 | Mandrel for installing the wheel hub cap |
67:7853.9534 | Washer for pressing out the outer ring of the inner bearing of the front wheel hub |
67.7853.9535 | Handle to the washers for pressing the outer ring of the inner bearing of the wheel hub |
67.7853.9536 | Mandrel for pressing the outer ring of the front wheel hub bearing |
67.7853.9540 | Washer for pressing out the inner ring of the wheel bearing and oil seal |
67.8732.9501 | Rolling pin to control the geometric parameters of the front suspension cross member |
Rear suspension | |
67.7820.9517 | Rear Suspension Rod Pivot Replacement Kit |
Steering | |
A.47035 | Puller of ball pins of steering rods from the holes of the bipod and pendulum lever |
A.47043 | Steering arm puller |
А.74076/1 | Steering gear housing repair tool |
A.74076/R | Bracket for fastening the housing of the steering mechanism, attached to the device A.74076/1 |
A.74105 | Mandrel for pressing in and pressing out bushings of the shaft of the bipod of the steering mechanism |
A.74186 | Mandrel for pressing the outer rings of the worm shaft bearing |
A.90336 | Reamer for processing bushings of the steering gear housing |
67.7813.9504 | Tie Rod Clutch Wrench |
67.7824.9516 | Steering link ball pin puller |
67.7853.9541 | Mandrel for pressing and pressing the outer ring of the upper bearing of the worm |
67.8720.9501 | Steering wheel free play control device |
brakes | |
A.56124 | Wrench for brake pressure regulator plug |
67.7820.9519 | Rear brake pressure regulator installation tool |
67.7823.9519 | Brake drum puller |
electrical equipment | |
02.7823.9504 | Alternator Pulley Remover |
Body | |
A.78034 | Tool for removing the locking clip of the power window handle |