Transmission
1 - bottom cover; 2 - hole plug for checking the oil level; 3 - gear wheel of the second gear of the intermediate shaft; 4 - gear wheel of the III gear of the intermediate shaft; 5 - intermediate shaft (gear block); 6 - front bearing of the intermediate shaft; 7 - clamping washer bolt; 8 - clamping washer of the front bearing of the intermediate shaft; 9 - gear wheel of constant engagement of the intermediate shaft; 10 - thrust washer of the synchronizer spring of the IV gear of the input shaft; 11 - input shaft; 12 - front cover; 13 – an epiploon of a primary shaft; 14 - rear bearing of the input shaft; 15 - clutch housing; 16 - gearbox housing; 17 - breather; 18 - gear wheel of constant engagement of the input shaft; 19 - needle bearing of the front end of the secondary shaft; 20 – a ring gear of the synchronizer of IV transfer; 21 - sliding clutch of the synchronizer of IV and III gears; 22 – a blocking ring of the synchronizer of III transfer; 23 – a spring of the synchronizer of III transfer; 24 - gear wheel of the third gear of the secondary shaft; 25 - gear wheel of the second gear of the secondary shaft; 26 - hub of the sliding clutch of the synchronizer of I and II gears; 27 - secondary shaft; 28 - gear wheel of the 1st gear of the secondary shaft; 29 - bushing of the gear of the 1st gear of the secondary shaft; 30 - intermediate bearing of the secondary shaft; 31 - reverse gear of the secondary shaft; 32 – a core of the lever of a gear change; 33 - thrust pad; 34 - elastic sleeve; 35 - remote bushing; 36 - locking sleeve; 37 - outer cover of the gear lever; 38 – an internal cover of the gear lever; 39 - spherical washer of the ball bearing of the lever; 40 - gear lever; 41 – an epiploon of the back bearing of a secondary shaft; 42 - flange of the flexible coupling of the cardan shaft; 43 – a nut of the back end of a secondary shaft; 44 - sealant of the centering ring of the flexible coupling of the cardan shaft; 45 - centering ring of the flexible coupling of the cardan shaft; 46 - rear bearing of the secondary shaft; 47 - drive gear of the speedometer drive; 48 - speedometer drive; 49 – a back cover of a transmission; 50 – fork of inclusion of a backing; 51 - intermediate reverse gear; 52 - reverse gear of the intermediate shaft; 53 – an axis of an intermediate gear wheel of a backing; 54 - gear wheel of the 1st gear of the intermediate shaft; 55 - magnet; 56 - magnetic plug
Gearshift drive
1 – a fork of inclusion of a backing; 2 - retracting spring of the gear lever; 3 - guide cup of the lever; 4 - ball bearing of the lever; 5 - gearshift lever; 6 - spherical washer; 7 – lever spring; 8 - retaining ring; 9 - damper locking sleeve; 10 - elastic damper bushings; 11 - damper remote bushing; 12 – a persistent pillow of a damper; 13 – a core of the lever of a gear change; 14 - fork off III and IV gears; 15 – fork of inclusion of I and II transfers; 16 – a rod of a fork of inclusion of I and II transfers; 17 – a rod of a fork of inclusion of III and IV transfers; 18 – a rod of a fork of inclusion of a backing; 19 - block crackers; 20 - cover of clamps; 21 - bushing; 22 - retainer spring; 23 - lock ball; 24 – a back cover of a transmission; 25 - reverse lamp switch; 26 – the remote plug of a rod of a plug of a backing
The vehicle is fitted with a four-speed gearbox (see fig. Transmission), and on some cars - a five-speed with synchronizers in all forward gears.
The four-speed gearbox consists of primary 11, secondary 27 and intermediate 5 shafts, crankcase 16 and gear shift mechanism.
The input shaft 11 is made in one piece with the gear 18 of constant mesh. It rotates on two ball bearings, the front one is pressed into the socket of the end of the crankshaft, the rear bearing 14 is placed in the gearbox housing and sealed with an oil seal 13.
The secondary shaft 27 is mounted in three bearings. The front needle bearing 19 is installed in the bore of the input shaft, the middle bearing 30 is a ball bearing, pressed into the seat of the gearbox housing 16, the rear bearing 46, located in the seat of the rear cover 49, is sealed with an oil seal 41. Gear 28 of the first gear, gear are freely located on the secondary shaft 25 second gear, gear 24 third gear; they are in constant engagement with the gears of the same name of the intermediate shaft.
At the front end of the secondary shaft there are three splines, on which the hub of the sliding clutch 21 of the synchronizer of III and IV gears is located. The hub 26 of the sliding clutch of I and II gears is connected to the shaft in the same way. Reverse gear 31 is keyed to the shaft. On the rear neck of the shaft there is a drive gear 47 of the speedometer drive. The flange 42 of the flexible coupling of the cardan shaft is mounted on the splines of the shaft and is fixed with a nut 43.
The intermediate shaft 5 is made as one piece with the gear unit and is supported by two bearings; front bearing 6 - ball, fixed on the shaft with washer 8 and bolt 7, rear bearing - roller, cylindrical. Reverse gear 52 is located on the splines of the shaft.
The reverse intermediate gear 51 rotates freely on the axis 53, pressed into the holes of the crankcase of the box and its rear cover 49.
Synchronizers of all gears have the same design. Each of them consists of a hub 26, a clutch 21, blocking rings 22 and springs 23.
The hub is rigidly connected to the output shaft. A sliding sleeve is located on the outer splines of the hub. The blocking ring with its inner crown is connected to the synchronizer crown of the gear of any forward gear and is constantly pressed towards the sliding clutch.
Gear shifting is carried out using a mechanical drive, consisting of three rods 16, 17, 18 (see fig. Gearshift drive), on which forks 14, 15, 1 are fixed, which are included in the undercuts of the sliding clutches of the forward gear synchronizers. And fork 1 enters the annular recess of the intermediate reverse gear.
The five-speed gearbox is made on the basis of the four-speed one. The fifth gear is located in the cavity of the rear cover 24 (see fig. Rear of the five-speed gearbox), whose form has been changed accordingly. On the back of the output shaft 1, the reverse driven gear 2 and the hub 3 of the V gear synchronizer clutch are attached with one key.
The gear 8 of the fifth gear rotates on the sleeve 10. The fifth stage drive receives from the gear block 23, which is mounted on the splines of the intermediate shaft 25 and fastened to them with a bolt 22. An additional support for the gear block is a cylindrical roller bearing 21.