Controls of the car VAZ-1111: 1 - instrument panel; 2 - cigarette lighter; 3 - heater casing; 4 - gear lever; 5 - parking brake lever; 6 - handle of the cover of the heater casing; 7 - ashtray; 8 - carburetor air damper control knob; 9 - accelerator pedal; 10 - switch (lock) ignition; 11 - brake pedal; 12 - wiper switch lever; 13 - clutch pedal; 14 - horn switch; 15 - alarm switch; 16 - control lamp for covering the air damper of the carburetor; 17 - fog lamp switch; 18 - rear window heating switch; 19- hood lock drive handle; 20 - rear window wiper switch; 21 - headlight switch lever; 22 - turn signal switch lever; 23 - instrument cluster; 24 - outdoor lighting switch; 25 - heater fan switch; 26 - deflector; 27 - heater tap control lever; 28 - control lever for the air intake hatch cover.
The shift pattern is printed on the shift knob. Engage reverse gear only when the vehicle is completely stopped.
To engage reverse gear, press the lever all the way down and move it to the extreme right position. Then push the lever back.
Switch (lock) ignition, combined with an anti-theft device, is located on the right side of the steering column. The key in the lock can take one of four positions.
Position «III» - the ignition is off. The key is removed. With the key removed, the steering is locked. To turn off the anti-theft device, insert the key into the ignition switch and, turning the steering wheel slightly to the right and left, turn the key from the position «III» clockwise.
Position «0» - everything is off. The key cannot be removed, the steering is unlocked.
Position «I» - the ignition is on. The key cannot be removed, the steering is unlocked.
Position «II» - Ignition and starter included. The key cannot be removed, the steering is unlocked. It is achieved by turning the key clockwise against the force of the spring. In this position, the key is not fixed - for the starter to work, it must be held by hand.
To brake the vehicle with the parking brake, lift the lever all the way up (with a properly adjusted brake no more than 7 clicks). At the same time, the control lamp on the instrument panel will light up with a flashing red light.
To brake the car, pull the lever up a little, press the button on the end of the lever handle and lower it all the way down. The control lamp should go out.
By pressing the button of the outdoor lighting switch to the first fixed position, the side lights and license plate lights are turned on. At the same time, the control lamp in the instrument cluster lights up green.
By pressing the button to the second fixed position, the dipped or main beam headlights are additionally switched on (depending on the position of the steering column switch).
Heated rear door glass is activated by pressing the switch with the ignition on (to the left of the steering column on the instrument panel). At the same time, the control lamp in the upper shoulder of the key will light up (shown by arrow).
To turn on the rear fog light, press the switch (to the left of the steering column on the instrument panel) with the dipped or high beam headlights on. At the same time, the control lamp in the upper shoulder of the key will light up (shown by arrow).
To turn on the alarm, press the switch button (to the left of the steering column on the instrument panel). At the same time, all direction indicators and the control lamp installed in the switch light up with a flashing light...
... as well as a warning lamp for turning on the alarm and direction indicators on the instrument cluster. Pressing the button again turns off the alarm.
If you need to signal with high beam headlights, move the stalk switch lever towards you several times. In this position, the lever is not fixed.
To turn on the low beam headlights, move the stalk switch to the up position (the outdoor light switch must be in the second position).
To turn on the high beam headlights, move the stalk switch to the lower position (outdoor lighting switch - in the second position).
If you need to turn on the left turn signal, move the stalk lever down to the stop. When the steering wheel is returned to the straight ahead position, the lever will automatically return to the neutral position.
If you need to turn on the right turn signal, move the stalk lever up to the stop. When the steering wheel is returned to the straight ahead position, the lever will automatically return to the neutral position.
The windshield wiper and washer switch lever is located on the steering column on the right. in neutral (top) lever position is off.
Move the lever down a little and turn on the first fixed position - the windshield wiper will work intermittently.
Move the lever down to the stop in the lower fixed position - the wiper will work continuously.
If you need to turn on the windshield washer, push the lever towards you.
To turn on the rear door glass cleaner, press the switch (to the left of the steering column on the instrument panel) and move it to the first fixed position.
Further pressing the key (transferring it to the second non-fixed position) the rear window washer is switched on.
To turn on the horn, press the button located on the steering wheel.
When pulling the carburetor choke control knob towards you (closing the carburetor choke)...
... the control lamp on the instrument panel lights up (to the left of the steering column).
To turn on the heater fan motor at low speed, press the fan switch button, moving it to the first fixed position.
To turn on the heater fan motor at high speed, move the key to the second fixed position.
Lever 1 is used to control the air intake hatch cover (when it is moved to the right position, the manhole cover opens), lever 2 - to control the heater valve (when it is moved to the right position, the valve opens). The operation of the interior ventilation and heating system is discussed in more detail in subsection 1.12.
To adjust the direction of air flow, deflectors are located at the top center of the instrument panel. By turning them, you can change the direction of air flow (on the windshield, in the passenger compartment, on the glass of the side doors).
By opening the heater cover, you will provide air to the driver's and passenger's feet and to the windshield. To direct the airflow to the windshield only, the cowl cover must be closed.