Exterior body repair VAZ-1111 Oka

In this section, articles about the device and repair of external elements of the body of the car VAZ-1111 Oka.

Features of the frame structure and body plumage
The main elements of the frame are the front, floor, side panels, roof with windshield frame, rear panel and power elements (side members, cross members, pillars and other parts)....

Features of the front door device
The doors consist of outer and inner panels. The door hinges are attached to the front pillars of the body with bolts. The doors on the hinges have height and transverse...

Features of the rear doors
Hangs on two loops 6 (figure 172). The lock 9 is attached to the bottom of the inner door panel. The lock retainer 11 is fixed to the crossbar of the rear body. The enlarged holes...

Features of the hood device
It consists of external and internal panels, connected to each other by bending flanges with glue (figure 173). Expansion spacers are installed between the panels. Figure 173....

Features of the bumper and radiator grille design
Bumpers They are made of frost-resistant polypropylene. The front bumper is attached to the body at the front with two bolts and two latches and additionally with holders at the...

Features of the windshield washer device
The windshield washer provides cleaning of the glass in any operating conditions of the car. The washer consists of a supply tank from the VAZ-21081 car, a pressure pump assembled...

Possible bodywork faults
Possible body malfunctions, their causes and methods of elimination. The door does not lock The rivet of the external drive lever axle is loose. When closing, the lever tooth does...

Checking and repairing the body frame and plumage
A significant portion of body repair work is performed on damaged vehicles, which, in most cases, require checking the geometry of the attachment points of the vehicle chassis...

Repair of deformed surfaces
Repair of damaged parts is carried out by drawing, straightening, straightening with metal shrinkage, cutting out areas that cannot be repaired, making repair inserts from...

Removal and installation the front wing
Disconnect the ground terminal of the battery. With the bumper removed, unscrew the two screws securing the radiator grille. Remove the socket with the turn signal bulb from the...

Roof panel replacement
Remove the windshield, tailgate, roof trim, assemblies and parts that impede straightening and welding work. Use a 6-7 mm drill to drill out contact welding points where the roof...

Replacing the rear panel
Replacement must be carried out with the rear bumper, assemblies and parts that interfere with the work removed. Drill out contact welding points with the mating parts: sidewalls,...

Front doors — removal, disassembly and adjustment
Removal and installation Open the door until it stops, unscrew the screws securing the eye of the limiter 3 (figure 181) door opening to the front pillar and bolts 2 fastening...

Tailgate — Removal and Installation
Removal the door Remove the brush, disconnect the electrical wires and the glass washer tube, open the door all the way and unscrew the stop pins 2 ( see figure 172 ) from...

Removal and installation the hood
Disconnect the windshield washer tube from the tee on the hood. Holding the hood 4 ( see figure 173 ) unscrew the four bolts securing the hood to the hinges 5 and remove the hood...

Removal and installation bumpers
To remove the front bumper 3 (figure 183) disconnect the electrical wires from the direction indicators, unscrew the bolts 5 of the front mount, unscrew the nuts of the holders 1...

Removal and installation the radiator grille
To remove the lining 3 (figure 184) unscrew six screws 1 at the front of the car, two screws on each side of the trim at the top and two screws on the bottom edges. Remove flange...

Removal and installation the outside rearview mirror
Use a screwdriver to remove the plug of the internal handle of the mirror, unscrew the screw and remove the handle and mirror. Unscrew three screws and remove the mirror support...

Replacement of windshield, side glass and tailgate
To remove a damaged windshield, remove the wiper arm, tuck the edges of the glass seal at the top behind the body opening flange and, pressing on the upper corners of the glass,...

Polishing of the body paintwork
To preserve the paintwork for a long time and keep it in good condition, it is necessary to select polishing agents that correspond to the condition of the coating. During the...

Repainting the body with synthetic enamel
Preparing the paint To obtain a high-quality coating, it is very important to prepare the paint correctly: select the color, bring the paint to working viscosity, filter the...

Repairing paintwork damage
Due to the complexity of color matching, it is recommended to eliminate damage to the paintwork by repainting the entire body panel. After replacing body parts (wing, door panels,...

Anti-corrosion protection of the body
The car body has a significant number of closed (hidden) cavities, cracks, which create favorable conditions for the occurrence and development of corrosion, as they are poorly...

This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

More articles from other manuals on VAZ cars:
➠ Body: Exterior VAZ-2121 (1977-1994)
➠ Body: Exterior VAZ-2110 (1995-2007)
➠ Body: Exterior VAZ-2107 (1982-2012)
➠ Body: Exterior VAZ-2114 (2004-2013)
➠ Body: Exterior VAZ-21061 (1976-2006)

Share with friends: