English Русский
Български
Беларускі
Український
Српски
Hrvatski
Română
Polski
Slovenský
Magyar
| Articles | Contacts | Sitemap |   
Repair and maintenance Lada Repair and maintenance Mazda Repair and maintenance Mitsubishi Repair and maintenance Toyota Repair and maintenance Land Rover Repair and maintenance Hyundai Repair and maintenance Nissan
VAZbook.ru
 
 
 
 
 
 
 
 
 
Main     1111   2101   2105   2106   2107   2109   2110   2115   2121  
VAZ-2104 (1984-2012) VAZ-2105 (1979-2010) VAZ-21051 (1979-2010)
  • Main
  • «Zhiguli»
  • VAZ-2105
  • Power unit
  • Engine repair
  • Removal and installation the camshaft drive belt

Removal and installation the camshaft drive belt (VAZ-2105)

            0

Contents: Removal ↓ Installation ↓

Removal



The sequence of operations for removing the belt is as follows:
  • disconnect the wires from the battery;
  • unscrew the nut securing the generator to the tension bar, turn the generator and remove the drive belt.
  • set the gear shift lever to neutral position;
  • remove the upper protective cover of the camshaft drive;
  • turn the crankshaft until the marks on the camshaft pulley align with the mark on the cylinder head cover, and the marks on the crankshaft pulley align with the long mark on the camshaft drive cover (see fig. 73);
  • remove the middle and lower protective covers of the camshaft belt drive;
  • remove the tension roller bracket spring;
  • loosen the bracket mounting bolts, move it to the extreme left position and remove the camshaft drive belt.

Installation



Install the new belt in the following order:
  • put the belt on the crankshaft pulley and, pulling the belt counterclockwise, put it on pulley 8 (see fig. 19) auxiliary drive roller and tension roller 4;
  • place the belt from the front end onto the camshaft pulley 5, pressing the bracket 6 to the right, and install the spring 7.

Install the middle protective cover of the belt drive without tightening the mounting bolts. Smoothly turn the crankshaft two revolutions, keeping the belt under constant tension and without loosening it when the shaft stops. Check the alignment of the timing marks on the camshaft pulley and the cylinder head cover, as well as on the crankshaft pulley with the long mark on the middle protective cover. If the marks match, tighten the 3 bolts securing the tension roller bracket, first the right bolt, then the left. If the marks do not match, repeat the belt installation operation, adjusting the position of the camshaft pulley.



Install and secure the lower, middle and upper camshaft belt cover. Put on the alternator drive belt and adjust its tension. Connect the wires to the battery, check and adjust the ignition timing if necessary.

[The text is copied from the online resource: VAZbook.ru]


This article is available at russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian
The text was reviewed by the specialist: Grigory Vologodtsev

Share with friends:

Previous articles
VAZ-2105: Engine repair
Next articles

Removal and installation the camshaft
Design of the camshaft and its drive
Checking the technical condition and repairing the cylinder head
Disassembly and assembly of the cylinder head
Removal and installation the cylinder head
Removal and installation the camshaft drive chain
Checking the technical condition of the camshaft parts
Possible engine malfunctions
Removal and installation the engine
Disassembling the engine

More articles from other manuals on VAZ cars:
➠ Adjusting the tension of the camshaft drive belt VAZ-1111 (1988-1996)
➠ Checking the condition of the camshaft drive belt VAZ-2109 (1984-1997)
➠ Replacing the camshaft drive belt VAZ-2115 (1997-2012)
➠ Fan, water pump, generator drive belt tension VAZ-2101 (1970-1983)
➠ Replacing the camshaft drive chain damper VAZ-21061 (1976-2006)
Link in different formats to this page


Visitor comments

No comments yet


How much will 44 + 18 ?

       






VAZ-2104 (1984-2012) 
  • General information
  • Operation and maintenance
  • Power unit
  • Engine repair
  • Fuel system (carburetor)
  • Fuel system (injector)
  • Control system
  • Cooling system
  • Exhaust system
  • Transmission
  • Clutch
  • Car gearbox
  • Cardan gear
  • Rear axle
  • Chassis
  • Front suspension
  • Rear suspension
  • Wheels and tires
  • Steering
  • Brake system
  • Body
  • Exterior
  • Interior
  • Doors and glass
  • Ventilation and heating
  • Electrical equipment
  • Equipment and devices
  • Headlights and lighting
  • Engine electrics
  • Electrical circuits

 

VAZ-2105 (1979-2010) 
  • General information
  • Vehicle description
  • Vehicle device
  • Vehicle operation
  • Maintenance
  • Power unit
  • Engine repair
  • Cooling and lubrication system
  • Supply system
  • Transmission
  • Clutch
  • Car gearbox
  • Cardan gear
  • Rear axle
  • Chassis
  • Suspension and shock absorbers
  • Steering
  • Brake system
  • Body
  • Body elements
  • Electrical equipment
  • Engine electrics
  • Equipment and devices

 

VAZ-21051 (1979-2010) 
  • General information
  • Introduction to guide
  • User manual
  • Troubleshooting
  • Power unit
  • Engine repair
  • Engine repair VAZ-2103
  • Cooling system
  • Lubrication system
  • Power and exhaust system
  • Fuel injection
  • Transmission
  • Clutch
  • Car gearbox
  • Cardan gear
  • Rear axle
  • Chassis
  • Suspension and shock absorbers
  • Steering
  • Brake system
  • Body
  • Exterior
  • Interior
  • Doors and windows
  • Electrical equipment
  • Equipment and devices
  • Engine electrics
  • Ignition system
  • Electrical circuits

 

VAZbook.ru © 2017 · Mobile version · Contact with administration · Sitemap: EN BG BY UA RS HR RO PL SK HU · Site search · News and articles VAZ-1111 · VAZ-11113 · VAZ-2101 · VAZ-21011 · VAZ-2104 · VAZ-2105 · VAZ-21051 · VAZ-2106 · VAZ-21061 · VAZ-2107 · VAZ-21099 · VAZ-2109 · VAZ-2108 · VAZ-2110 · VAZ-2112 · VAZ-2114 · VAZ-2115 · VAZ-2121 · VAZ-21213 · VAZ-21214 ·
The site stores technical data using cookies to improve the service.