Car gearbox repair VAZ-2110

All articles on the device and repair of mechanical gearbox units of VAZ-2110 (Lada 110) cars and their modifications.

Gearbox — device and description
The VAZ 2110, VAZ 2111 and VAZ 2112 cars are equipped with a mechanical, five-speed, two-shaft gearbox, combined with the main gear and differential in a common housing. It...

Gearbox — technical condition check
Before proceeding to check the technical condition of the gearbox, we make sure that the clutch release and gear shift mechanisms are in good working order and correctly adjusted...

Gearbox — Checking the oil level
We check the oil level in the gearbox during vehicle maintenance, as well as before each trip if there is an oil leak from the gearbox. We check the oil level in the gearbox with...

Gearbox — Oil change
It is recommended to change the oil in the gearbox after 75,000 km of mileage of the VAZ 2110, VAZ 2111, VAZ 2112 car or after five years, depending on what comes first. Helpful...

Jet thrust — removal and installation
Removal 1. Prepare the vehicle for repair work (see points 1 and 2b, " Preparing a car for maintenance and repair "). 2. Using a socket wrench with a 13 mm head and a spanner of...

Jet thrust — disassembly and assembly
Disassembly 1. Remove the jet thrust (see " Jet thrust - removal and installation "). If you plan to install a complete thrust rod on your vehicle, use a marker, felt-tip pen or...

Gear shift drive — removal, installation and adjustment
To perform gear shift adjustment you will need: inspection pit or overpass; assistant; roulette. Removal 1. Prepare the vehicle for repair work (see points 1 and 2b, " Preparing a...

Gear shift drive — disassembly and assembly
Disassembly 1. Remove the gear shift drive from the vehicle (see " Gear shift mechanism drive - removal, installation and adjustment "). 2. Using a 13 mm wrench, unscrew the gear...

Gearbox — removal and installation
Recommendation: The gearbox weighs over 30 kg, so work should be done with an assistant or using an adjustable stop or lifting device. Removal 1. Remove the engine protection (see...

Gearbox — disassembly and assembly
Note. This section describes the complete disassembly of the gearbox: primary shaft, secondary shaft and differential, which is necessary for a major overhaul of the gearbox. To...

Gearbox — disassembly of housings, inspection
1. Using a 17 mm socket wrench, unscrew the powertrain support bracket mounting bolt. 2. Using a 17 mm open-end wrench, unscrew the two nuts securing the rear cover of the gearbox...

Primary shaft of the gearbox — disassembly and assembly
Disassembly 1. Clamp the primary shaft in a vice with soft metal pads and press it with two mounting blades... ...and remove the ball bearing from the input shaft. 2. From the...

Secondary shaft of the gearbox — disassembly and assembly
Warning: If the synchronizer locking rings are in good condition, mark them when disassembling them so that they can be reinstalled in their original positions later. Disassembly...

Gearbox differential — disassembly and assembly
Warning: When replacing the differential bearings or its housing, it is necessary to re-select the thickness of the adjusting ring (see " Gearbox adjusting ring - selection of...

Gearbox — assembly
1. Clean the mating surfaces of the gearbox housings from traces of old sealant. 2. Wash the gearbox housings and other parts with diesel fuel or kerosene and wipe them dry....

Differential adjusting ring — selection of rings
We select the differential adjustment ring in such a way as to ensure a preload of 0.25 mm on the differential bearings. Sequence of work execution 1. Install new bearings of the...

Gearbox replacement of front wheel drive seals
Note: Replacing the front wheel drive seals is performed without removing the gearbox from the vehicle. Warning: Right and left drive oil seals are not interchangeable (Part...

Replacing the gearbox primary shaft seal
Removal 1. Remove the gearbox from the car (see " Gearbox - removal and installation "). 2. Remove the clutch parts from the housing (see " Clutch release drive elements installed...

Replacing the gear selector rod seal
Removing the gear selector rod seal is shown when disassembling the gearbox and clutch housings. 1. Using a 17 mm socket wrench, unscrew the powertrain support bracket mounting...

This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

More articles from other manuals on VAZ cars:
➠ Transmission: Car gearbox VAZ-21011 (1974-1983)
➠ Transmission: Car gearbox VAZ-2115 (1997-2012)
➠ Transmission: Car gearbox VAZ-2105 (1979-2010)
➠ Transmission: Car gearbox VAZ-21213 (1994-2006)
➠ Transmission: Car gearbox VAZ-2107 (1982-2012)

Share with friends: