This section contains articles on the removal, disassembly, repair and assembly of the engine of VAZ-2110 (Lada 110) cars and their modifications.
Car engine — device and description On cars VAZ 2110, VAZ 2111, VAZ 2112, a gasoline, four-stroke, four-cylinder in-line engine with an overhead camshaft and liquid cooling is installed. The cylinder block is cast...
Checking the engine oil level It is recommended to check the oil level 10-15 minutes after stopping the engine. Work sequence 1. We prepare the car for work (see item 2a " Preparing the car for maintenance and...
Changing the oil and oil filter on a car The first oil and oil filter change on a new or overhauled engine is after 2000-3000 kilometers, then every 15,000 km. The volume of oil in the engine lubrication system is 3.5...
Decorative engine cover — removal and installation Removing 1. We prepare the car for work (see item 2a " Preparing the car for maintenance and repair "). On the injection engine VAZ 2112 (l,5i): 2. Using a 10 mm socket wrench,...
Checking the oil pressure in the engine lubrication system If, when the engine is warmed up to operating temperature at idle, the emergency oil pressure lamp lights up, make sure that: A) there are no extraneous sounds coming from the...
Checking compression in the engine cylinders To check the compression pressure in the engine cylinders, you will need: assistant; compression gauge. Compression test sequence 1. We prepare the car for work (see item 2a "...
Crankshaft pulley — removal, installation, replacement To perform the work of removing, installing, replacing the crankshaft pulley, you will need: assistant; viewing hole or flyover. Removing 1. Remove the front right wheel (see...
Front timing belt cover — removal and installation Note. Work on removing and installing the front timing belt cover is shown on the VAZ 21124 injection engine (1,6i). On the VAZ 2112 engine (1,5i) The front timing cover is not...
Timing belt — removal, installation, replacement Camshaft drive scheme on VAZ 2110, VAZ 2111, VAZ 2112 cars: 1 - toothed pulley of the engine crankshaft; 2 - tide on the cover of the oil pump; 3 - toothed pulley of the coolant...
Front crankshaft oil seal — replacement Removing 1. Remove the crankshaft pulley and its key (see " Crankshaft toothed pulley - removal, installation, replacement "). Warning. When removing the oil seal, do not scratch...
Camshaft pulleys — removal, installation, replacement To remove, install, replace the camshaft pulleys, you will need a special tool to hold the camshaft pulleys. Note. Removal, installation, replacement of the camshaft pulley can be...
Rear timing belt cover — removal and installation Removing 1. Remove the camshaft pulleys (see " Camshaft pulleys - removal, installation, replacement "). 2. Remove the tension and guide rollers (see " Timing belt tensioner and...
Camshaft seals — replacement Removing 1. Remove the camshaft pulley (see " Crankshaft toothed pulley - removal, installation, replacement "). 2. If the key was not removed after removing the pulley, remove it...
Cylinder head cover — removal, installation, replacement Note. Removal, installation, replacement of the cylinder head cover is shown on the VAZ 21124 engine (1,6i). Features of removing, installing, replacing the cylinder head cover of...
Camshafts — removal, installation, replacement Note. Removal, installation, replacement of camshafts is shown on the injection engine VAZ 21124 (1,6i). Features of removing the cylinder head cover from the VAZ 2112 engine...
Hydraulic lifters — removal, installation, replacement Removing 1. Remove the camshafts (see " Camshafts - removal, installation, replacement "). 2. When assembling, it is recommended to install hydraulic lifters in their original...
Oil seals — replacement Recommendation. Replace valve stem seals on a VAZ 2112 engine (1,5i) you can try without removing the head from the cylinder block. To do this, it is necessary to set the piston...
Cylinder head — removal and installation Note. The engine cylinder head can be removed from the car as an assembly or, after partial disassembly, the camshafts can be removed. Both options are shown on the VAZ 21124...
Cylinder head — check To perform a cylinder head test on a vehicle, you will need: a special template or a wide locksmith's ruler; flat feeler set. Check sequence 1. Remove the head from the car (see "...
Valves — removal, lapping and installation of valves Note. We perform valve grinding on the removed cylinder head (see " Cylinder head - removal and installation "). To grind valves, you must have: valve grinding tool; rubbing...
Flywheel — removal, installation, replacement Removing 1. Remove the pressure and clutch discs (see points 1-3 " Driven and pressure plates of coupling - replacement "). 2. Using a 17 mm socket wrench, unscrew the six bolts...
Rear crankshaft oil seal — replacement Removing 1. Remove the flywheel (see " Flywheel - removal, installation, replacement "). Warning. When performing the following operation, do not scratch the working surface of...
Oil receiver — removal, installation, replacement Removing 1. Remove the engine oil pan from the car (see " Engine oil pan - removal "). 2. With a 10 mm key, unscrew the two bolts (1) fixing the oil receiver to the main bearing...
Oil pump — removal, disassembly, assembly and installation Removing 1. Remove the crankshaft pulley and its key (see " Crankshaft toothed pulley - removal, installation, replacement "). 2. Remove the engine oil pan (see " Engine oil pan -...
Piston rings — replacement To carry out repair work to replace the piston rings, you will need a special mandrel. Removing 1. Remove the cylinder head from the car (see " Cylinder head - removal and...
Piston and connecting rod — replacement To replace pistons and connecting rods you will need: caliper; mandrel for piston rings. Disassembly 1. Remove the piston rings from the piston (see " Piston rings - replacement...
Engine mounts and rods — removal and installation Left engine mount To complete the work you will need: height-adjustable stop (e.g. screw jack); viewing hole or flyover. Removing 1. We prepare the car for work (see items 1, 2b...
Removal and installation of the engine assembly Note. To remove the engine from the vehicle, a lifting device with a lifting capacity of at least 200 kg is required. If there is no such device, then the engine can be partially...
Engine repair with complete disassembly Disassembly 1. Remove the cylinder head (see " Cylinder head - removal and installation "). 2. Remove the oil receiver (see " Oil receiver - removal "). 3. Remove the oil pump...