Cooling and lubrication system VAZ-21213

All articles on the device and repair of components and assemblies of the cooling and lubrication system for the engine of VAZ-21213 Niva cars.

Cooling system device
The design of the cooling system is shown in Fig. 2-60. Fig. 2-60. Engine cooling system: 1 - radiator drain hose; 2 - thermostat; 3 - thermostat bypass hose; 4 - hose for...

Checking the level and density of the liquid in the cooling system
The correct filling of the cooling system is checked by the liquid level in the expansion tank, which on a cold engine (at 15-20°C) should be 3-4 cm above the "MIN" mark on the...

Filling the cooling system with coolant
Filling is performed when changing the coolant or after engine repair. Filling operations are performed in the following order: remove the plugs from the radiator and expansion...

Adjusting the tension of the pump drive belt
The belt tension is checked by its deflection between the generator and pump pulleys or between the pump and crankshaft pulleys. With normal belt tension, deflection A (Fig. 2-61)...

Coolant pump
Disassembly To disassemble the pump: disconnect the pump body 5 (Fig. 2-62) from the cover 3; secure the cover in a vice using spacers and remove impeller 2 (Fig. 2-63) from the...

Checking the Thermostat
The thermostat should be checked for the temperature at which the main valve starts to open and for the valve stroke. To do this, install the thermostat on the BS-106-000 stand,...

Removal, inspection and repair of the radiator
Removal from the vehicle To remove the radiator from the car, do the following: remove the spare tire and remove the spare tire support tube; drain the fluid from the radiator and...

Lubrication system device
The design of the lubrication system is shown in Fig. 2-67. Fig. 2-67. Lubrication system: 1 - oil supply channel to the main bearing; 2 - oil supply channel from the main bearing...

Engine oil change
The oil must be changed on a warm engine. To completely drain the oil, you must wait at least 10 minutes after opening the drain hole. When changing the oil, you should also...

Removal, disassembling and checking the oil pump
The main dimensions of the pump parts and its drive are shown in Fig. 2-68. Removal and installation If only the oil pump needs to be repaired, remove the engine from the vehicle...

Oil pump drive shaft and gears
There should be no dents or scratches on the surfaces of the roller support journals and on the working surface of the eccentric. The teeth of the oil pump and distributor drive...

Engine crankcase ventilation system
Flushing the system To flush, disconnect hoses 4 and 5 (Fig. 2-75) of the ventilation system from the pipes, remove flame arrester 3 from the exhaust hose 5, remove cover 6 of oil...

Features of the engine cooling system of the VAZ-21214-10 car
The cooling system features are expressed in the installation of two electric fans 14 (Fig. 9-21). The casing with electric fans is installed in front of the radiator and is...

Features of the engine cooling system of the VAZ-21215-10 car
Features of the device Closed-type cooling system with forced circulation of coolant, with an expansion tank (Fig. 9-28). Fig. 9-28. Cooling system: 1 - expansion tank steam...

Lubrication system of the VAZ-21215-10 car engine
Features of the device The lubrication system is combined. The bearings of the crankshaft and camshafts, the bearings of the shaft and the gear of the oil pump drive are...

This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

More articles from other manuals on VAZ cars:
➠ Power unit: Cooling system VAZ-2112 (1999-2007)
➠ Power unit: Cooling and lubrication system VAZ-11113 (1996-2003)
➠ Power unit: Cooling and lubrication system VAZ-21061 (1976-2006)
➠ Power unit: Cooling system VAZ-21011 (1974-1983)
➠ Power unit: Cooling and lubrication system VAZ-21099 (1990-2004)

Share with friends: