Repair of fuel system components VAZ-21213

All articles on the device and repair of components and assemblies of the fuel supply system for the engine of VAZ-21213 Niva cars.

Air filter and thermostat — removal and installation
To remove the air filter, press the spring holders 14 (Fig. 2-76) and unscrew the nut 7 securing the air filter cover 8. Remove the cover and take out the filter element 10. Fig....

Fuel tank — removal, installation and inspection
Removal and installation To remove fuel tank 1 (Fig. 2-78), disconnect the ground wire from the battery. Fig. 2-78. Fuel tank parts and fuel lines: 1 - fuel tank; 2 - separator...

Fuel pump device
The fuel pump device is shown in Fig. 2-79. Fig. 2-79. Fuel pump: 1 - discharge pipe; 2 - filter; 3 - body; 4 - suction pipe; 5 - lid; 6 - suction valve; 7 - traction; 8 - manual...

Checking the fuel pump
Insufficient filling of the carburetor with gasoline may be due to a faulty fuel pump, as well as clogged or damaged fuel lines. To find the cause of the malfunction, disconnect...

Disassembling, cleaning and checking fuel pump parts
To disassemble the pump, unscrew the cover mounting bolt 5 ( see fig. 2-79 ), remove the cover and filter 2. Then unscrew the screws securing the housing to the bottom cover,...

Installing a fuel pump on an engine
To properly install the fuel pump on the engine, use two of the three gaskets listed below: A - 0.27-0.33 mm thick; B - 0.70-0.80 mm thick and C - 1.10-1.30 mm thick. The pump...

Features of the carburetor device
The engine is equipped with a 21073-1107010 carburetor (Fig. 2-81) of the emulsion type, two-chamber, with sequential opening of the throttle valves. The carburetor has a balanced...

Removal and installation a carburetor on a car
Removal and installation should be performed only on a cold engine. To do this, remove the air filter. Disconnect it from the lever 1 ( fig. 2-81 ) throttle drive rod 15 (Fig....

Disassembling the carburetor
Loosen the screws securing the carburetor cover and carefully remove it so as not to damage the gasket, float and tubes of the economizer and the transition system of the second...

Cleaning and checking the technical condition of carburetor parts
Fuel filter Wash the filter in gasoline and blow it with compressed air. Check the condition of the filter. If the filter or fuel supply pipe is damaged, replace them with new...

Assembling the carburetor
Assemble the carburetor in the reverse order of disassembly. Pay attention to the following points. The float should rotate freely on its axis without touching the walls of the...

Adjusting and checking the carburetor
Setting the fuel level in the float chamber The fuel level required for normal operation of the carburetor is ensured by the correct installation of serviceable elements of the...

Exhaust gas recirculation system
The vehicle is equipped with an exhaust gas recirculation system consisting of a thermal vacuum switch 2 (Fig. 2-92) and a recirculation valve 5 with a channel and recirculation...

Exhaust gas system
Exhaust gases are discharged from the engine through the exhaust manifold, intake pipe 2 (Fig. 2-93), then through the additional muffler 7 and the main muffler 6. Fig. 2-93....

Central injection unit of the VAZ-21214 car
Removal and installation Place the gear shift lever in neutral and apply the parking brake. Since fuel pressure remains in the fuel system after the engine has stopped, the...

Power supply system of the VAZ-21214-10 car engine
The fuel system is part of the electronic engine management system, which is described in detail in a separate Manual for repair and maintenance of the engine management system...

Crankcase ventilation system of the VAZ-21214-10 car
Forced ventilation is used to remove gases and gasoline vapors from the crankcase, which is accomplished by sucking gases from the crankcase into the engine intake pipe. Crankcase...

Exhaust system of the VAZ-21214-10 car
Exhaust gases are discharged from the engine through the exhaust manifold, inlet pipe 2 (Fig. 9-23), neutralizer 11, additional muffler 15 and main muffler 13. Fig. 9-23. Exhaust...

Power supply system of the VAZ-21215-10 car engine
Features of the device The fuel system consists of a fuel tank, fuel filter, high-pressure fuel pump (HPFP), injectors, air filter, intake pipe, low and high pressure fuel lines....

Exhaust gas release of the VAZ-21215-10 car
Exhaust gases are discharged from the engine through gas receiver 3 (Fig. 9-33), intake pipe 4, neutralizer 9, additional muffler 13 and main muffler 11. Fig. 9-33. Exhaust gas...

Power supply system of VAZ-2129 and VAZ-2131 cars
On vehicles with two fuel tanks, the filler necks are connected to one hatch. The filler neck of the main fuel tank is at the rear, and the additional one is at the front (in the...

This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

More articles from other manuals on VAZ cars:
➠ Power unit: Power and exhaust system VAZ-21051 (1979-2010)
➠ Power unit: Power and exhaust system VAZ-21061 (1976-2006)
➠ Power unit: Fuel system VAZ-11113 (1996-2003)
➠ Power unit: Supply system VAZ-2110 (1995-2007)
➠ Power unit: Supply system VAZ-2109 (1984-1997)

Share with friends: