Instruction Manual VAZ-21213

All articles describing everyday functions for the daily operation of VAZ-21213 Niva cars and their modifications.

Introduction to the Operation and Maintenance Manual
This Manual is a guide to vehicle maintenance and repair. It is intended for service station specialists, motor pools and repair shops, as well as individual vehicle owners. The...

Technical characteristics of cars
Table 1-1. Technical characteristics of cars Table 1-2. Distinctive parameters of long-wheelbase vehicles Table 1-3. Main parameters of the VAZ-2130 engine

Vehicle controls
The location of the controls is shown in Fig. 1-4. 1 - sound signal switch. 2 - instrument cluster panel. 3 - steering wheel. On a vehicle with an airbag-equipped steering wheel,...

Instrument cluster
The instrument cluster is shown in Fig. 1-5. 1 - tachometer. The electronic device indicates the engine crankshaft rotation frequency. The yellow zone of the scale indicates the...

Interior ventilation and heating controls
Ventilation and heating of the passenger compartment are regulated depending on the outside air temperature. Fig. 1-6. Interior ventilation and heating controls: 1 - side nozzles...

Starting the engine
Cold engine starting 1. Set the gearshift lever to neutral. If the ambient temperature is below zero, press the clutch pedal. 2. Pull out the carburetor choke handle, insert the...

Electronic anti-theft system
Some of the manufactured cars are equipped with an electronic anti-theft system, which ensures that the engine can be started only after reading the code from the working code...

Operation of the anti-theft system APS-2R
Disabling the immobilizer To disarm the immobilizer: 1. Open the driver's door or turn on the ignition. In this case, the immobilizer switches from the security mode to the...

Operation of the anti-theft system APS-4
Disabling the immobilizer The immobilizer in the security mode blocks the engine from starting. In this mode, the immobilizer status LED flashes at a frequency of 1 time per 2.5...

Alternative engine start
Vehicles with the MP 7.0 engine management system controller have the option of alternative engine start without using a code key. Alternative engine start is possible only after...

Position of the transfer case levers
The differential lock lever can take the following positions (Fig. 1-9): R - unlocked; B - blocked. When the lever is moved to this position, a warning lamp lights up in the...

Vehicle movement
Before starting to move, check the position of the transfer case levers - the gear shift lever should be in the "high gear" position, and the differential lock lever in the...

Braking and parking
The brakes are designed to provide effective braking. However, try to brake smoothly and moderately in all cases, avoiding sudden braking. Do not turn off the ignition or remove...

Precautions when operating a vehicle
During the first 2000-3000 km of a new car: 1. Before each trip, check and adjust the air pressure in your tires to the correct level. 2. Avoid driving on difficult roads (deep...

Car body care
The body is the basic and most expensive element of the car. It is made of modern materials and protected from corrosion by high-quality protective agents. The basis for the...

Car storage
When operating, pay close attention to the storage conditions of the car, since with an annual mileage of 15 thousand km, the car is in motion for about an hour a day. The optimal...

Vehicle maintenance
During the operation of the vehicle, its technical condition deteriorates due to wear of the rubbing surfaces of the parts, violation of the adjustment parameters, aging of rubber...

Tightening torques for threaded connections
Detail Thread Tightening torque, Nm (kgf·m) Engine Main bearing cap fastening bolt M10x1.25 68,31-84,38 (6,97-8,61) Oil pump mounting bolt M6 5,10-8,20 (0,52-0,85) Breather cap...

Special tool for repair and maintenance
Designation Name Engine A.40005 Universal Puller Set A.40026 Coolant Pump Impeller Puller A.50088 Wrench for intake and exhaust pipe fastening nuts A.50113 Engine Oil Drain Plug...

Basic data for adjustments and control
Clearances in the valve drive mechanism between the cams and levers on a cold (18-20°C) engine, mm: for intake valves - 0.15 for exhaust valves - 0.20 Temperature of the liquid in...

Fuels, lubricants and operating fluids used
* For vehicles with a fuel injection system equipped with an exhaust gas neutralizer, use only unleaded gasoline AI-95. ** Recommended operating temperature range: 5W-30 - from...

This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

More articles from other manuals on VAZ cars:
➠ General information: Operation manual VAZ-2115 (1997-2012)
➠ General information: User manual VAZ-21051 (1979-2010)
➠ General information: Operation and maintenance VAZ-21011 (1974-1983)
➠ General information: User manual VAZ-21099 (1990-2004)
➠ General information: User manual VAZ-2110 (1995-2007)

Share with friends: