Suspension and shock absorber repair VAZ-21213

All articles about the device and repair of the suspension, shock absorbers, wheels and tires of VAZ-21213 Niva cars.

Possible suspension faults, their causes and methods of elimination
Noise and knocking in the suspension when the car is moving Cause of malfunction Method of elimination 1. The shock absorbers are faulty. 1. Replace or repair shock absorbers. 2....

Front suspension device
The front suspension device is shown in Fig. 4-1. Fig. 4-1. Front suspension: 1 - front suspension cross member; 2 - axle of the lower suspension arm; 3 - rubber-metal hinge of...

Determining the condition of the front suspension parts
During each maintenance, as well as during repairs, it is necessary to check the condition of the protective covers of the ball joints of the suspension, paying special attention...

Checking and adjusting the front wheel alignment angles
Checking and adjusting the front wheel alignment angles is performed on special stands in accordance with the stand instructions. Warning: Checking the wheel alignment is...

Checking and adjusting the clearance in the front wheel hub bearings
To check the clearance, remove the hubcap and loosen the wheel nuts, lift the front of the car, support it on a stand and remove the front wheel. Remove the front brake caliper...

Replacing grease in front wheel hub bearings
To replace the grease, perform the following operations on both sides of the vehicle: after raising the front of the car, remove the wheel; bending back the edges of the front...

Removal and installation the front suspension
Place the vehicle on a lift or inspection pit, apply the parking brake, open the hood and remove the spare wheel. Place chocks under the rear wheels and remove the front wheels....

Disassembly and assembly of front suspension units
Disassembly If the suspension repair requires complete disassembly of its components, it is more convenient to start this directly on the car, after removing the protective...

Checking the technical condition of the front suspension
Ball joints Make sure the ball joint mudguards are intact; breaks, cracks, separation of rubber from metal reinforcement, traces of lubricant leakage are unacceptable. Check for...

Replacement of rubber-metal hinges
Upper arm Between the lever eyes, install the device 67.7823.9527 on the axle and place the lever on the mandrel A.47045 (Fig. 4-10). Using the press punch, press on the axle 1 of...

Rear suspension device
The rear suspension device is shown in Fig. 4-14. Fig. 4-14. Rear suspension: 1 - spacer sleeve; 2 - rubber bushing; 3 - lower longitudinal bar; 4 - lower spring insulating...

Removal and installation the rear suspension
Removal Raise the rear of the car and place it on stands. Remove the rear wheels. Disconnect the propeller shaft from the main gear pinion flange. Disconnect the brake hydraulic...

Checking the technical condition of the rear suspension
Before checking, rinse all parts thoroughly. Protect rubber parts, bushings and protective coatings from solvents when washing. Springs Check the elastic characteristics of the...

Shock absorber device
The design of the shock absorbers of the front and rear suspensions is shown in Fig. 4-18. Fig. 4-18. Front and rear suspension shock absorbers: 1 - lower eye; 2 - compression...

Checking shock absorbers on a stand
To determine the performance of the shock absorber, check its operating diagram on a dynamometer stand. Record the operating diagrams according to the instructions supplied with...

Disassembly and assembly of the shock absorber
After external washing, secure the shock absorber in a vice. Note: To secure the shock absorber and its parts in a vice, use special jaws 67.7824.9513-001. Having pulled the shock...

Checking the technical condition of shock absorber parts
Wash the metal parts and dry them, and wipe the rubber parts with a clean cloth and rinse with warm water. Please check carefully that the parts comply with the following...

This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

More articles from other manuals on VAZ cars:
➠ Chassis: Car suspension VAZ-2112 (1999-2007)
➠ Chassis: Car suspension VAZ-21011 (1974-1983)
➠ Chassis: Car suspension VAZ-2109 (1984-1997)
➠ Chassis: Suspension and shock absorbers VAZ-21051 (1979-2010)

Share with friends: