Disarming the immobilizer
To disarm the immobilizer:
1. Open the driver's door or turn on the ignition. In this case, the immobilizer switches from the armed mode to the «Reading», and LED 1 of status indicator 2 blinks at a rate of 2 times in 1 s. If the transition to the reading mode is made by turning on the ignition, the buzzer will emit a short beep.
2. In mode «Reading», which lasts 2 minutes, bring it to the status indicator 2 «Mine» working key 3 and wait for the LED to turn off. When the key code is read, the LED lights up briefly with constant light, and the buzzer emits a double beep. Turning off the LED provides the opportunity to start the engine.
Setting the immobilizer to guard
The transition of the immobilizer to the armed mode occurs automatically after the ignition is turned off, and the installation time depends on the situation and the driver's actions. The LED in armed mode flashes at a frequency of 1 time per 4 s. The immobilizer is armed after 5 minutes if the door has not been opened, or after 1 minute - from the moment the door is opened.
The anti-theft system provides for accelerated arming. To do this, immediately after turning off the ignition for 2 seconds, turn the ignition back on and immediately turn the ignition off again within the next 2 seconds. In this case, the activation of the anti-theft system is reduced to 15 seconds..
In all cases, 15 seconds before the system is armed, the buzzer starts beeping at an accelerating rate. If arming is undesirable, then turn the key to position «Ignition».
Mode «Education»
The red key is teaching. Required to activate the mode «Education», at which it is possible to teach the immobilizer the codes of new working keys or, for example, to replace the lost ones. (In total, up to four working keys can be trained. If more than four keys are learned, then each new one will erase the code of the key that was written first from the immobilizer's memory.)
To enable the mode «Education» you need to enter the mode «Reading» and then perform the following procedure:
1. Bring «Mine» red key to the status indicator and while holding it, wait for the LED to turn off. When reading the key code, the LED lights up with a constant light and then goes out.
Remove the key from the status indicator within 3 s after the LED turns off. If everything is done in time, the LED resumes its indication with a frequency of 5 times in 1 s. This indicates the inclusion of the mode «Education».
2. To confirm the mode «Education» within the next 3 s from the beginning of rapid flashing (5 times in 1 s) bring the red key close to the status indicator again, and after the LED lights up briefly with a constant light, move it away again.
After that, start learning working keys. To do this, they must be brought in turn to the status indicator. After the key code is recognized and stored in the memory of the immobilizer, the LED lights up at 1 with constant light, and the buzzer emits a short beep. The maximum time between key learning is 10 s. If during this time the next learning key is not brought up, the immobilizer will exit the mode «Training Finish Mode «Education» also possible by presenting a red key. In mode «Education» LED flashes 5 times per 1 s.
Maintenance mode
An additional function of the anti-theft system is the maintenance mode. This mode is characterized by the fact that the immobilizer does not prevent the engine from starting and can be useful when transferring control to another person without transferring the code keys to him or when servicing the car when the automatic arming function interferes with work. The status of the immobilizer in maintenance mode is displayed in two ways:
- when the ignition is off, the LED flashes at a frequency of 2 times in 4 s;
- When the ignition is switched on, the LED lights up continuously as long as the ignition is switched on.
Entering and exiting the maintenance mode occurs only after activating the maintenance mode «Education». To do this, while confirming the learning mode, continue to hold the red key at the status indicator until the LED turns off. The LED goes out for 3 s, and the immobilizer switches to one of the following modes:
- if the immobilizer was in the mode «Education», then it goes into maintenance mode, and the LED starts flashing at a frequency of 2 times every 4 s;
- if the immobilizer was in the maintenance mode, then it exits this mode and remains in the maintenance mode «Education» keys.
Entering and exiting the maintenance mode ALWAYS results in erasing the working key codes from the immobilizer memory. Therefore, when exiting the maintenance mode, the transition of the immobilizer to the learning mode is due to the need to learn the working keys. The immobilizer is taught the key codes according to the previously described method.
1. If the anti-theft system is in maintenance mode, then entering the mode «Reading» only done by opening the door.
2. The key learning procedure, as well as entering and exiting the maintenance mode, must be carried out only behind closed doors.