Car engine repair VAZ-2114

This section contains articles on the removal, disassembly, repair and assembly of the engine of VAZ-2114 (Lada Samara 114) and their modifications.

Engine specifications
Table 8.1.1. Basic data for monitoring, adjustment and maintenance Engine cylinder firing order 1-3-4-2 Clearances in the timing mechanism drive on a cold engine (18-20°C), mm: ...

Description of engine design
The car is equipped with a gasoline, four-stroke, four-cylinder, in-line, eight-valve engine with an overhead camshaft and liquid cooling, models 2111 or 11183. Cross section of...

Engine — technical condition check
The technical condition of the engine depends on the vehicle's mileage, the timeliness of periodic maintenance, the quality of the operating materials used, and the quality of the...

Lubrication system — checking the oil level
Recommendation: The check should be carried out 10-15 minutes after the engine has been stopped. 1. Prepare the car for work (see " Preparing the car for maintenance and repair...

Lubrication system — oil and oil filter replacement
The first oil change on a new or overhauled engine is after 2000-3000 km of mileage, then every 15,000 km. The volume of the lubrication system is 3.5 liters. Recommendation: For...

Decorative engine trim 11183 (1.6i) — removal and installation
The decorative trim is held in place by four rubber couplings placed on the studs of the cylinder head cover and receiver. Removal 1. Prepare the car for work (see " Preparing the...

Lubrication system — checking oil pressure
Recommendation: If the oil pressure warning light comes on while the engine is idling and warmed up to operating temperature, you must make sure that: a) the oil level in the...

Compression in engine cylinders — check
To complete the work you will need an assistant and a compression gauge. 1. Prepare the car for work (see " Preparing the car for maintenance and repair "). 2. Check and, if...

Timing Belt — Checking Condition and Adjusting Tension
The timing belt should be checked during vehicle maintenance - every 15,000 km. To perform the work you will need a timing belt tensioner key. Sequence of execution 1. Prepare the...

Timing Belt — Replacement
An assistant will be required to complete the work. Removal 1. Remove the front timing belt cover (see " Timing Belt - Checking Condition and Adjusting Tension "). 2. Remove the...

Timing Belt Tensioner Roller — Replacement
1. Remove the front timing belt cover (see " Timing Belt - Checking Condition and Adjusting Tension "). Recommendation: When replacing the tension roller without removing the...

Front Crankshaft Oil Seal — Replacement
1. Remove the timing belt (see " Timing Belt - Replacement "). 2. Remove the toothed pulley from the crankshaft. 3. To avoid losing the key, remove it from the groove. Warning:...

Camshaft Seal — Replacement
1. Remove the timing belt (see " Timing Belt - Replacement "). Tip: For ease of operation, you can remove the windshield washer reservoir (see " Windscreen washer reservoir -...

Intake manifold and exhaust manifold gasket — replacement
To carry out the work you will need an inspection pit or overpass. Removal 1. Prepare the vehicle for work and disconnect the battery (see " Preparing the car for maintenance and...

Cylinder Head Cover Gasket — Replacement
Removal 1. Prepare the car for work (see " Preparing the car for maintenance and repair "). WITH engine 11183 (1.6i) remove the decorative trim (see " Decorative engine trim 11183...

Adjusting the clearances in the timing drive valves
Note: A gap is required between the camshaft cam and the valve tappet to compensate for thermal expansion of the valve stem. For intake valves, the gap should be 0.15-0.25 mm, and...

Camshaft — Removal and Installation
Removal 1. Remove the timing belt (see " Timing Belt - Replacement "). 2. Unscrew the nut and bolt of the upper fastening of the rear timing belt cover (see " Coolant pump -...

Valve stem seals — replacement
To complete the work you will need: valve spring compressor; tweezers; valve stem seal remover; cap pressing mandrel; tin rod; magnet. Removal 1. Remove the camshaft (see "...

Cylinder head — removal and installation
The cylinder head is removed for its repair, for replacing the head gasket, and also during major engine repairs. Removal 1. Prepare the vehicle for work and disconnect the wire...

Cylinder head — check
To complete the work you will need: a special template or a wide metalworking ruler; set of flat feeler gauges. Sequence of execution 1. Remove the cylinder head (see " Cylinder...

Valves — lapping
Checking the condition of the valves and grinding them in must be performed if, when checking the compression in the cylinders (see " Compression in engine cylinders - check ")...

Flywheel — removal and installation
Removal 1. Remove the pressure and driven clutch discs (see " Clutch - replacement "). 2. Using any available method, mark the position of the flywheel on the shaft. 3. With a...

Rear Crankshaft Oil Seal — Replacement
Removal 1. Remove the flywheel (see " Flywheel - removal and installation "). Warning: When performing the following operation, be careful not to scratch the running surface of...

Engine Oil Pan — Gasket Replacement
Removal 1. Remove the engine splash guard (see " Engine Mudguard - Removal and Installation "). 2. Drain the oil from the engine (see " Lubrication system - oil and oil filter...

Oil intake — removal and installation
Removal 1. Remove the engine oil pan (see above, " Engine Oil Pan - Gasket Replacement "). 2. Key by 10 mm we unscrew the two bolts (1) securing the oil intake to the main bearing...

Oil pump — removal, disassembly, inspection, assembly and installation
To complete the work you will need: micrometer (from 0 to 25 mm); calipers (with a measurement limit of 0.05 mm); plumbing (metal) ruler. Removal 1. Remove the crankshaft toothed...

Piston rings and connecting rod bearings — replacement
To complete the work you will need: piston ring mandrel; torque wrench. Removal 1. Remove the cylinder head (see " Cylinder head - removal and installation "). 2. Remove the...

Connecting rod and piston group with a floating pin
To complete the work you will need: bore gauge; a rod made of soft metal (0.21 mm) or a special mandrel. Disassembly 1. Remove the piston rings from the piston (see " Piston rings...

Connecting rod and piston group with pressed-in pin
The replacement of the connecting rod and piston group with a pressed-in pin is carried out in the same sequence as the replacement of the connecting rod and piston group with a...

Left Engine Mount — Removal and Installation
To complete the work you will need: height adjustable stand (screw or hydraulic jack); inspection pit or overpass. Removal 1. Prepare the car for work (see " Preparing the car for...

Front Engine Mount — Removal and Installation
To complete the work you will need: height adjustable stand (screw or hydraulic jack); inspection pit or overpass. Removal 1. Prepare the car for work (see " Preparing the car for...

Rear Engine Mount — Removal and Installation
To complete the work you will need: height adjustable stand (screw or hydraulic jack); inspection pit or overpass. Removal 1. Prepare the car for work (see " Preparing the car for...

This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

More articles from other manuals on VAZ cars:
➠ Electrical equipment: Engine electrics VAZ-2104 (1984-2012)
➠ Power unit: Engine repair VAZ-21011 (1974-1983)
➠ Power unit: Engine repair VAZ-2107 (1982-2012)
➠ Power unit: Engine repair VAZ-2112 (1999-2007)
➠ Electrical equipment: Engine electrics VAZ-21213 (1994-2006)

Share with friends: