| List of maintenance works | Methods of execution or reference to relevant chapters | Vehicle mileage (±500), thousand km | |||||||
| 2.5 | 15 | 30 | 40 | 50 | 50 | 90 | 105 | ||
| Engine and its systems | |||||||||
|
Make sure there are no extraneous noises or knocks when the engine is running* Check the tightness of the fasteners of the power unit supports* Lubrication system - make sure there is no oil leakage through sealing gaskets, oil seals* Lubrication system - replace oil and oil filter Timing drive - check the condition and tension of the belt* Timing belt drive - replace belt Cooling system - make sure there are no coolant leaks, check the condition of the hoses, pipes and radiator* Cooling system - check the coolant level in the expansion tank* Cooling system - replace coolant** Engine fuel system - check the tightness of fuel supply components* Engine fuel system - replace fuel filter Engine fuel system - replace air filter element Engine Management System - Check System Functionality* Engine Management System - Check Engine Management System ECU Memory for Trouble Codes* Engine Management System - Replace Spark Plugs Engine Management System - Replace Oxygen Sensor Exhaust system - check the tightness of the system, the condition of the muffler suspension elements* |
by ear cm. Tightening torques for threaded connections inspection Oil and oil filter change Timing belt - checking condition and adjusting belt tension Timing belt - removal, installation, replacement inspection Checking the coolant level and the tightness of the cooling system Replacing the coolant inspection Fuel filter - replacement Air filter - replacing the filter element by the control lamp diagnostic equipment at service stations Spark plugs - replacement Oxygen Concentration Sensor - Checking and Replacing by ear and inspection (i'll give you some carbon) |
X X X X — — X — — X — — X X — — X |
X X — X X — X X — X — — X X — — X |
X X X X X — X X — X X X X X X — X |
X X — X — X X X — X — — X X — — X |
X X X X X — X X — X X X X X X — X |
X X — X X — X — X X — — X X — X X |
X X X X — X X X — X X X X X X — X |
X X — X X — X X — X — — X X — — X |
| Clutch | |||||||||
|
Make sure there are no extraneous noises when engaging and disengaging the clutch* Check the clutch pedal travel and adjust the clutch release drive* |
Checking the technical condition of the clutch Clutch release drive - adjustment |
X X |
X X |
X X |
X X |
X X |
X X |
X X |
X X |
| Transmission | |||||||||
|
Make sure there are no oil leaks through seals and oil seals* Check the condition of the gearshift rod protective boots* Check the clarity of gear shifting, make sure there are no extraneous noises or knocks when the gearbox is operating* Check the gearbox oil level* Change gearbox oil** |
inspection inspection Gearbox - technical condition check Gearbox - Checking the oil level Gearbox - Oil change |
X X X — — |
— X X X — |
X X X — — |
— X X X — |
X X X X — |
— X X — X |
X X X X — |
— X X X — |
| Front wheel drives | |||||||||
|
Make sure there are no extraneous noises in the drive joints when the vehicle is moving straight and on turns* Check the condition of the anthers* |
by ear inspection |
X X |
X X |
X X |
X X |
X X |
X X |
X X |
X X |
| Wheels and tires | |||||||||
|
Check the condition of tires, wheel rims* Balance the wheels |
Front suspension - device, description at the service station |
X X |
— — |
X X |
— — |
X X |
— — |
X X |
— — |
| Front suspension | |||||||||
|
Make sure there are no extraneous noises in the front suspension when the car is moving over uneven surfaces* Adjust the angles (collapse, convergence) wheel installations Check the condition of the front suspension components* |
by ear at the service station inspection |
X X X |
X — X |
X X X |
X — X |
X X X |
X — X |
X X X |
X — X |
| Rear suspension | |||||||||
|
Make sure there are no extraneous noises or knocks in the rear suspension when the car is moving over uneven surfaces* Check the condition of the rear suspension components* |
by ear inspection |
X X |
X X |
X X |
X X |
X X |
X X |
X X |
X X |
| Steering | |||||||||
|
Check the condition of the tie rod and steering gear boots* Check the play in the steering* |
inspection see table below - Basic data for adjustments and control |
X — |
X X |
X X |
X X |
X X |
X X |
X X |
X X |
| Brake system | |||||||||
|
Make sure there are no brake fluid leaks, check the condition of the brake hoses and brake pipes* Check the fluid level in the brake master cylinder reservoir* Replace brake fluid in the brake system** Check the operation of the handbrake* Check the efficiency of the front and rear wheel brakes* Check the wear of the brake pads of the front wheel brake mechanisms* Check the wear of the brake pads of the rear wheel brake mechanisms* Make sure the brake booster is working properly* Check the functionality of the brake pressure regulator* |
inspection Checking the brake fluid level in the master cylinder reservoir Brake pedal free play - checking and adjusting Checking and adjusting the handbrake at the service station Front brake pads - checking for wear Rear brake pads - checking for wear Master brake cylinder - removal, installation, replacement Rear brake fluid pressure regulator - adjustment |
X — — X X — — — — |
X X — — X X — — — |
X X — X X X X — X |
X — X — X X — X — |
X X — X X X X — X |
X X — — X X — — — |
X — X X X X X X X |
X X — — X X — — — |
| Electrical equipment | |||||||||
|
Generator - check condition and tension of generator drive belt* Generator - make sure the generator is working properly* Generator - clean contact rings, check wear of generator brushes Starter - clean the rotor collector, check wear, lubricate drive elements Battery - clean, lubricate terminals and posts Battery - check electrolyte level and density* Lighting and light signalling - make sure lamps are working properly* Headlight Hydraulic Corrector - Check Functionality* Headlights - adjust the direction of the headlights Control devices - make sure the lamps are working properly* Sound signal - check for functionality* Windscreen wipers and washers - check that they are working properly* Rear window heating - check for proper operation* Electric window lifts - check for proper operation* Electric drive of exterior mirrors - check for functionality* Seat heating - check that it is working* |
Generator Drive Belt - Checking and Adjusting Tension Generator - check without removing from the car Generator - disassembly, parts inspection and assembly Starter - repair Battery - Removal and Installation Battery - Check inspection with the lights on by turning the handle with the low beam on Headlight unit - light adjustment inspection with ignition on inclusion enabled in all modes included with the glass sealed inclusion inclusion inclusion |
— X — — — — X X — X X X X X X X |
X X — — — X X X — X X X X X X X |
X X — — X X X X — X X X X X X X |
X X — X — X X X X X X X X X X X |
X X X — X X X X — X X X X X X X |
X X — — — X X X — X X X X X X X |
X X — X X X X X X X X X X X X X |
X X — — — X X X — X X X X X X X |
| Body | |||||||||
|
Door, hood, and trunk lid locks - make sure they are working properly* Door, hood, and trunk lid locks - lubricate Hood lock drive cable - lubricate Lubricate the hinges and door stops Drainage holes in doors and thresholds - clean |
opening and closing cm. Body maintenance cm. Hood Lock Drive Cable - Lubrication and Replacement |
X — — — — |
X — — X X |
X X — X X |
X — X X X |
X X X X X |
X — X X X |
X X X X X |
X — X X X |
| Ventilation and heating system | |||||||||
|
Filter element of the cabin ventilation system - replace Heater - make sure it is working* |
cm. Cabin Ventilation Filter - Replacement switching on in all modes |
— X |
X X |
X X |
X X |
X X |
X X |
X X |
X X |
|
* The detected malfunction must be corrected.
** If the vehicle has low mileage, replace after 5 years. |
|||||||||
Note. Maintenance of the car after 120,000 km of mileage is not regulated by the factory. During further operation of the car, you can be guided by the list specified in the table, reducing the mileage between maintenance. The mileage between maintenance should be determined based on the operating conditions and service life of the car, but not more than 10,000 km.
Basic data for adjustments and control on the vehicle
Timing belt deflection under a load of 100 N (10 kgf) in the middle between the camshaft pulleys — 5.2-5.6 mm
The coolant level in the expansion tank on a cold engine is up to the upper mark or to the upper edge of the fastening belt
The gap between the spark plug electrodes is 1.00-1.13 mm
Clutch pedal working stroke: 120-130 mm
Front wheel alignment:
- equipped vehicle - 0.5-2.5
- at a load of 3.2 kN (320 kgf) - ±1 mm
Front wheel alignment:
- equipped vehicle — 0°-1°00'
- at a load of 3.2 kN (320 kgf) - 0°±30'
Longitudinal tilt of the front wheel pivot axis:
- equipped vehicle — 0°-1°30'
- at a load of 3.2 kN (320 kgf) - 1°-2°30'
The difference in longitudinal inclination of the axle of the right and left front wheels, no more than - 1°
Free play of the steering wheel in the position corresponding to the straight-line movement of the vehicle, no more than - 5°
Working stroke of the parking brake lever is 2-4 teeth
Free travel of the brake pedal with the engine not running - 3-5 mm
The brake fluid level in the master cylinder reservoir with the cover removed is up to the "MAX" mark
The density of the electrolyte in the battery is 1.26-1.28 g/cm³.
Generator drive belt deflection under a load of 100 N (10 kgf) — 6-8 mm